Agilent Technologies 81101A - page 40

40

Programming Reference

SCPI Instrument Command List

Command :ARM:IMP

Long :ARM[:SEQuence[1]|STARt][:LAYer]:IMPedance

Form Set & Query

Parameter Numeric

Parameter Suffix OHM with engineering prefixes, e.g.: MOHM is Megaohms.

*RST value 50 Ω

Specified Limits 50 Ω or 10 kΩ

Description Use this command to program the input impedance of the EXT INPUT

connector. Note that only two settings are available. If you try to program

any other value, it will be rounded to one of the specified values.

Example To set up the input impedance and the triggering threshold of the EXT

INPUT connector:

Command :ARM:LEV

Long :ARM[:SEQuence[1]|STARt][:LAYer]:LEVel

Form Set & Query

Parameter Numeric

Parameter Suffix V with engineering prefixes.

*RST value +1.0 V

Specified Limits –10 V to +10 V

Description Use this command to program the triggering threshold of the EXT INPUT

connector.

Example To set up the input impedance and the triggering threshold of the EXT

INPUT connector:

:ARM:IMP 50OHM

:ARM:LEV 2.5V

Set EXT INPUT impedance to 50 Ω

Set EXT INPUT threshold to 2.5 V

:ARM:IMP 50OHM

:ARM:LEV 2.5V

Set EXT INPUT impedance to 50 Ω

Set EXT INPUT threshold to 2.5 V

Contents

Main MODIFY Front Panel Display and Softkeys Page Notice Copyright Notice Warra nty Limitation of Warranty Exclusive Remedies Certification Services and Support Safety Summary General Environmental Conditions Before Applying Power Ground the Instrument Fuses Do Not Operate in an Explosive Atmosphere Do Not Remove the Instrument Cover Safety Symbols About this Book Conventions Used in this Book Page Contents Page The GP-IB Interface Bus Agilent 81101A Remote Control Programming Recommendations Page Common Command Summary 19 General Programming Aspects Status Model Status Model Condition Register Transition Filters Event Register Enable Register Status Byte Standard Event Status Group OPERation Status Group QUEStionable Status Group 2 Agilent 81101A SCPI Command Summary Page Page Page Page Default Values, Standard Settings Page Page Page Programming the Instrument Trigger Modes Continuous Triggered Gated External Width Pulses Burst SCPI Instrument Command List Page Page Page Page Page Page Page Page Page Page Offset = High Low Page Page Page Page Period = 1 Frequency Page D elay = Phase 360 Period Width = Duty Cycle 100 Period Phase = Delay Period Delay% = Delay Period Page Page DblDel% = DblDel Period Page Frequency = 1 Page Page Page Page Page Page Page High = Offset + Amplitude Low = Offset Amplitude High = Offset + Amplitude Low = Offset Amplitude Page HighLow Offset = Page Page Page 77 5. :STATus:QUEStionable:PTRansition 4. :STATus:QUEStionable:NTRansition Page Page Page Page Page Page Page Page Page Page Page 3 90 Specifications Declaration of Conformity Declaration of Conformity Manufacturer Safety EMC Supplementary Information Agilent 81101A Specifications General Page Timing Specifications Period Glitch-free timing changes Width Delay Double Pulse Delay Transition Times Level Specifications External Load compensation Level Parameters Pulse Performance Clock Sources Clock / PLL Reference Input Phase Locked Loop (PLL) External Clock Output Modes Pulses Mode Burst Mode Trigger Modes 101 Specifications Agilent 81101A Specifications Trigger and Strobe Specifications Trigger Output Strobe Output Typical Delays Human Interface Memory Remote Control Pulse Parameter Definitions Time Reference Point Pulse Period Trigger Delay Pulse Width Pulse Delay Double Pulse Delay Interchannel Delay (Skew) Transition Time Linearity Jitter Stability Pulse Levels Preshoot, Overshoot, Ringing Settling Time Page Page Page Page Page Page Front Panel Controls Page MANUAL CHANGES September, 01 Page Page Page