Appendix C | Agilent Technologies E1470A specs

Appendix C

RF Switch Error Messages

The following error messages are unique to the E1470A. See the appropriate command module or VXI Controller module manual for a more complete list of possible error messages.

Error	Message Generated	Description	Commands that
Number			may cause error

-108	“Parameter not allowed”	A parameter was specified that is not valid for the
		command. More than 80 channels specified in
		command.	DIAG:OPEN;CLOS;DI:CLOS?;IAG:OPEN?

-222	“Data out of Range”	Invalid numerical state parameter.

-240	“Hardware Error”	More than 60 msec was required for the relays to	SAVRCL
		settle.	PC

2001	“Invalid channel number”	Invalid channel number in <source> parameter	*WAI?

2022	“Invalid relay number”	Invalid relay number in command

2023	“Invalid common bank	Invalid <comm> parameter in command.	DIAG:OPEN;CLOS;DI:CLOS?;IAG:OPEN?
	number”

2024	“Invalid source bank	Invalid source number in <source> parameter
	number”

2025	“Invalid Common-Source	Even though the <comm> and <source>
	Combination”	parameters are valid, the combination is not valid.
		The specified source cannot connect to the
		specified COM terminal.	[ROUT:]PATH[:COMM]?

Appendix C

RF Switch Error Messages 53

Image 53

Agilent Technologies E1470A user manual Appendix C RF Switch Error Messages

Contents

E1470-90002 Page Contents Appendix C RF Switch Error Messages Index Government Restricted Rights Agilent Technologies Warranty Statement Documentation History Safety Symbols Manufacturer’s Address Manufacturer’s NameDeclares, that the product Product Name Model NumberPage Chapter Using This ChapterSwitching Diagram Cascade Relays COM 33 332 Creating Multiple Multiplexers Configuring the RF Switch Chapter Maximum POWER. The maximum RF power that can be applied RF Switch ConfigurationChapter Configuring the RF Switch On this module Setting the Logical Address Setting the Interrupt Request Level Installing User Wiring Configuring the RF Switch Chapter Connecting User Wiring SMB Connectors and Connector Housings Assembling SMB Connector Jacks User Connections Wiring RF Switch Installing Device Drivers Programming the RF Switch Chapter Addressing the Switch Programming Examples Chapter Programming the RF Switch Programming the RF Switch Chapter Example Closing a Signal Path Example Opening Closing Signal Paths Example Saving Recalling Module States Programming the RF Switch Chapter Common Commands Format Command TypesScpi Commands Format Chapter RF Switch Command Reference RF Switch Command Reference Chapter Scpi Command ReferenceLinking Commands DIAGnosticCLOSe DIAGnostic DIAGnosticOPEN DIAGnosticCLOSe?DIAGnosticOPEN relay,relay... opens individual relays on Reset to its power-on state Common to NC DIAGOPEN333 DIAGnosticOPEN? RSTDIAGThis programCLOS042,043,053,054,256REL?returns DIAGnosticRELAY? ROUTePATHCOMMon ROUTe Example Closing Channel Path 10002 SYSTemVERSion? SYSTemERRor?SYSTem Command Ieee 488.2 Common Commands Quick Reference Description Commands Quick Reference Appendix a Appendix a RF Switch Specifications RF Switch Specifications Appendix a About This Appendix Appendix BRegister Addressing Addressing Overview Figure B-1. Register Address Locations Within VXI A16 Base Address A16 Address Space Outside the Command Module Table B-1. General Register-based Programming Method Register DefinitionsTable B-2. Register Map Register-Based Programming Appendix B Table B-4. Control Register Bit Pattern write Table B-3. Status Register Bit Patterns read Relay Control Registers Vxie Table B-10. Writing to Relay Control Registers Create and open a device session Register Programming Example Wait 5 seconds before resetting module Void errhandler /* Error Handling Routine Register-Based Programming Appendix B Appendix C Appendix C RF Switch Error Messages RF Switch Error Messages Appendix C Index Index Index E1470-90002