Index | Agilent Technologies E1470A instruction

	R	S
	register-based programming, 41	safety symbols, 6
	registers	SCPI commands
	base address, 42	abbreviated, 27
	definitions, 44	command reference, 28
	Device Identification, 45	command separator, 27
	Manufacturer ID, 45	format, 27
	offset, 43	implied, 28
	programming example, 49	linking, 28
	reading from, 47	parameter types, 28
	reset states, 44	quick reference, 38
	Status/Control, 45	specifications, RF switch, 39
	writing, 47	Status/Control register, 45
	relay states, definitions, 9	switching description, 9
	reset states, registers, 44	SYSTem subsystem, 36
	resource manager, 14	SYSTem:ERRor?, 36
	restricted rights statement, 5	SYSTem:VERSion?, 36
	RF switch
	addressing, 20	U
	error messages, 53	user wiring table, 18
	programming, 19	user wiring, connecting, 16
	specifications, 39	W
	[ROUTe:]PATH[:COMMon], 33	W
	[ROUTe:]PATH[:COMMon]?, 34	warnings, 6, 13
	[ROUTe:]PATH[:COMMon]?, 34	warranty statement, 5
	[ROUTe:] subsystem, 33	warranty statement, 5
	[ROUTe:] subsystem, 33	wiring table, user, 18
		wiring table, user, 18

56 Index

Image 56

Agilent Technologies E1470A user manual Index

Contents

E1470-90002 Page Contents Appendix C RF Switch Error Messages Index Agilent Technologies Warranty Statement Government Restricted Rights Safety Symbols Documentation History Manufacturer’s Name Manufacturer’s AddressDeclares, that the product Product Name Model NumberPage Chapter Using This ChapterSwitching Diagram Cascade Relays COM 33 332 Configuring the RF Switch Chapter Creating Multiple Multiplexers RF Switch Configuration Maximum POWER. The maximum RF power that can be appliedChapter Configuring the RF Switch On this module Setting the Logical Address Setting the Interrupt Request Level Connecting User Wiring Installing User Wiring Configuring the RF Switch Chapter Assembling SMB Connector Jacks SMB Connectors and Connector Housings User Connections Wiring Installing Device Drivers RF Switch Addressing the Switch Programming the RF Switch Chapter Chapter Programming the RF Switch Programming Examples Programming the RF Switch Chapter Example Closing a Signal Path Example Opening Closing Signal Paths Example Saving Recalling Module States Programming the RF Switch Chapter Command Types Common Commands FormatScpi Commands Format Chapter RF Switch Command Reference RF Switch Command Reference Chapter Scpi Command ReferenceLinking Commands DIAGnostic DIAGnosticCLOSe DIAGnosticCLOSe? DIAGnosticOPENDIAGnosticOPEN relay,relay... opens individual relays on Reset to its power-on state Common to NC DIAGnosticOPEN? DIAGOPEN333 DIAGnosticRELAY? RSTDIAGThis programCLOS042,043,053,054,256REL?returns ROUTe ROUTePATHCOMMon Example Closing Channel Path 10002 SYSTemVERSion? SYSTemERRor?SYSTem Ieee 488.2 Common Commands Quick Reference Command Commands Quick Reference Description Appendix a RF Switch Specifications Appendix a RF Switch Specifications Appendix a Appendix B About This AppendixRegister Addressing Addressing Overview Base Address Figure B-1. Register Address Locations Within VXI A16 A16 Address Space Outside the Command Module Register Definitions Table B-1. General Register-based Programming MethodTable B-2. Register Map Register-Based Programming Appendix B Table B-3. Status Register Bit Patterns read Table B-4. Control Register Bit Pattern write Relay Control Registers Vxie Table B-10. Writing to Relay Control Registers Register Programming Example Create and open a device session Wait 5 seconds before resetting module Void errhandler /* Error Handling Routine Register-Based Programming Appendix B Appendix C RF Switch Error Messages Appendix C RF Switch Error Messages Appendix C Index Index Index E1470-90002