Agilent Technologies E7401A, E7402A, E7403A, E7404A, E7405A Resolving Signals Example:

Chapter 1 15

Making Basic Measurements

Resolving Signals of Equal Amplitude

Resolving Signals Example:

Resolve two signals of equal amplitude with a frequency separation of

100 kHz.

1. Connect two sources to the analyzer input as shown in Figure1-4.

Figure 1-4 Setup for Obtaining Two Signals

2. Set one source to 300MHz. Set the frequency of the other source to

300.1 MHz. The amplitude of both sig n al s should be approximately

−20 dBm at the output of the bridge.

3. Set the analyzer as follows:

a. Press Preset, Factory Preset (if present).

b. Set the Y-Axis Units to dBm by pressing AMPLITUDE, More,

Y-AxisUnits, dBm .

c. Set the center frequency to 300MHz by pressing FREQUENCY,

Center Freq, 300, MHz.

d. Set the span to 2 MHz by pressing SPAN, Span, 2, MHz.

e. Set the resolution bandwidth to 300kHz by pressing BW/Avg,

Res BW, 300, kHz.

A single signal peak is visible. See Figure 1-5

NOTE If the signal peak is not present on the display, do the following:

1. Increase the span to 20MHz by pressing SPAN, Span, 20, MHz.

The signal should be visible.

2. Press Peak Search, FREQUENCY, Signal Track (On)

3. Press SPAN, 2, MHz to bring the signal to center screen.

4. Press FREQUENCY, Signal Track (Off)

Contents

Main Signal Analysis Measurement Guide Agilent Technologies EMC Series Analyzers Notice Safety Information Warrant y LIMITATION OF WARRANTY EXCLUSIVE REMEDIES Where to Find the Latest Informa tion Page Contents Page What is in This Chapter Test Equ ipm ent Comparing Signals Signal Comparison Example 1: Page Signal Comparison Example 2: Page Resolving Signals of Equal Amplitude Resolving Signals Example: Page Page Resolving Small Signals Hidden by Large Signals Resolving Signals Example: Page Page Making Better Frequency Measurements Better Frequency Measurement Example: Page Decreasing the Frequency Span Around the Signal Decreasing the Frequency Span Example: Page Page Tracking Drifting Signals Tracking Signal Drift Example 1: Page Page Tracking Signal Drift Example 2: Page Page Page Measuring Low Level Signals Measuring Low Level Signals Example 1: Page Measuring Low Level Signals Example 2: Measuring Low Level Signals Example 3: Page Measuring Low Level Signals Example 4: Page Page Identifying Distortion Products Distortion from the Analyzer Identifying Analyzer Generated Distortion Example: Page Page Third-Order Intermodulation Distortion Identifying TOI Distortion Example: Page Page Page Measuring Signal-to-Noise Signal-to-Noise Measurement Example: S/N 70 dB/Hz10 30 kHz()log+ 25.23 dB30 kHz()== Making Noise Measurements Noise Measurement Example 1: Page Page Page Page Noise Measurement Example 2: Noise Measurement Example 3: Page Page Demodulating AM Signals (Using the Analyzer As a Fixed Tuned Receiver) Demodulating an AM Signal Example 1: Page Page Page Page Page Demodulating FM Signals Demodulating a FM Signal Example: Page Page Page Page Whats in This Chapter Required Test Equipment Making Stimulus Response Measu rements What Are Stimulus Response Measurements? Using An Analyzer With A Tracking Generator Stepping Through a Transmission Measurement Page Page Page Page Tracking Generator Unleveled Condition Measuring Device Bandwidth Page Page Measuring Stop Band Attenuation Using Log Sweep Page Page Page Page Making a Reflection Calibration Measurement Example: Reflection Calibration Measuring the Return Loss Chapter 2 87 VSWR 110 Making Complex Measurements Making a Reflection Calibration Measurement -----------------------= Table 2-1 Power to VSWR Conversion + 110 Demodulating and Listening to an AM Signal Demodulating and Listening to an AM Signal Example 1: Demodulating and Listening to an AM Signal Example 2: