Manuals / Alamo / Lawn and Garden / Brush Cutter

Alamo SR20, SR14 manual Maintenance, Step

Models: SR14 SR20

1 166

Download 166 pages 37.06 Kb

Page 146

Image 146

MAINTENANCE

STEP 3

Remove the Hub Assembly from the vise and place it on a solid surface with the Gear in an upright position. Using a Hammer, tap this Gear downward until the Adjusting Nuts fully exposed. Remove the Cotter Pin. Remove the Adjusting Nut. FIGURE 28.

FIGURE 28

STEP 4

Laying the Hub Assembly on its side, tap the Gear end of the Output Shaft into the Gear and Bearing. Once the Shaft has cleared the Bearing, it can be fully removed from the Hub Assembly. The remaining Bearings and Bearing Cups can be removed by conventional means. FIGURE 29.

FIGURE 29

SR20M/SR14M 04/94

Maintenance Section 5-16

Page 146

Image 146

Alamo SR20, SR14 manual Maintenance, Step

Contents

RHINO OPERATORS MANUALFLEX-WING MECHANICAL LEVEL LIFT ROTARY CUTTER / SHREDDER SR20/ SR14TO THE OWNER/OPERATOR/DEALER before operating the Mower Safety Training Makes the DifferenceBE SAFE BE ALERT BE ALIVE BE TRAINED Please Send Me ASSEMBLY SECTION TABLE OF CONTENTSSAFETY SECTION MAINTENANCE SECTIONPage SAFETY SECTION Safety SectionSAFETY SAFETY¡LEA EL INSTRUCTIVO SAFETYSAFETY DANGER DANGER SAFETYSAFETY DANGER DANGER DANGERby the following rules SAFETYSAFETY DANGER SAFETYSAFETY KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglementDANGER SAFETYSAFETY DANGERDANGER SAFETYSAFETY QUENT FAILURE AND POSSIBLE SERIOUS INJURY FROM THROWNSTOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UNLESS SAFETYSAFETY DANGERDANGER SAFETYSAFETY DANGERNever unhitch without using the Tongue Jack. The Tongue is SAFETYSAFETY suddenly and unexpectedly could result in crushing injury. UseSEE YOUR SERVIS-RHINO DEALER SAFETYSAFETY SPRM-1SAFETY SAFETYLEVEL SAFETYSAFETY DESCRIPTIONSAFETY SAFETYSAFETY SAFETYSAFETY SAFETYSAFETY SR20 SR14SAFETY Employer-Employee Operator Regulations SAFETY FEDERAL LAWS AND REGULATIONSSAFETY This Act SeeksPage Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page INTRODUCTION SECTION Introduction SectionINTRODUCTION INTRODUCTIONASSEMBLY SECTION Assembly SectionBLADE CARRIER AND BLADES ASSEMBLYASSEMBLY LEVEL ROD ASSEMBLY ASSEMBLYASSEMBLY TONGUE ATTACHMENTWING SECTIONS ATTACHMENTS ASSEMBLYASSEMBLY HOSE BRACKET ATTACHMENTCENTER SECTION ASSEMBLYASSEMBLY LEVEL LIFT AXLE ATTACHMENT FIGUREAXLE ADJUSTMENT ROD ATTACHMENT ASSEMBLYASSEMBLY CENTER AXLE HYDRAULIC CYLINDER ATTACHMENTWING SECTION HYDRAULIC CYLINDER ATTACHMENT ASSEMBLYASSEMBLY TIRES AND WHEELSASSEMBLY ASSEMBLYBAFFLE KIT ASSEMBLY OPTIONAL ASSEMBLYASSEMBLY SPRING STOP ATTACHMENTASSEMBLY ASSEMBLYASSEMBLY ASSEMBLYDriveline Yoke ASSEMBLYASSEMBLY 11/16 Bolt EndCANOPY SHIELDS ASSEMBLYASSEMBLY THREE SPOOL CONTROL VALVE INSTALLATION ASSEMBLYASSEMBLY OPERATION SECTION Operation SectionRHINO SR14/SR20 ROTARY MOWER OPERATION INSTRUCTIONS OPERATIONOPERATION DANGER OPERATIONOPERATION PELIGROSR20 OPERATION Standard Equipment and SpecificationsOPERATION SR14OPERATION 1. OPERATOR REQUIREMENTSOPERATION Personal Protective Equipment PPEOPERATION 2. TRACTOR REQUIREMENTS2.2 Tractor Safety Devices OPERATIONOPERATION Tractor Drawbar LengthOPERATION Based on Mower Operating SpeedOPERATION 2.6 Front End Weight2.7 Power Take Off PTO OPERATIONOPERATION 3. GETTING ON AND OFF THE TRACTOROPERATION DANGEROPERATION 4. STARTING THE TRACTOROPERATION Safety Tow Chain OPERATION 5. CONNECTING THE MOWER TO THE TRACTOR5.1 Connecting the Mower Tongue to the Tractor OPERATIONOPERATION 5.2 Connecting Mower Hydraulic Lines to the TractorOPERATION Operating Mower Hydraulics with Three Tractor Hydraulic PortsLeveling Rod Adjustments OPERATION 6. SETTING THE MOWERSplit Collar Assemblies Leveling Rod Adjustments OPERATIONOPERATION 6.2 Setting Deck PitchOPERATION LEVELING WING SECTIONS WITH CENTEROPERATION 7. DRIVELINE ATTACHMENTOPERATION 7.1 Driveline Length CheckOPERATION “Bottoming Out” Check ProcedureEngagement Check Procedure OPERATIONOPERATION CV Driveline Maximum Angle Check ProcedureOPERATION 7.2 Constant Velocity CV DrivelineOPERATION 8. PRE-OPERATION INSPECTION AND SERVICEOPERATION DANGEROPERATION 8.1 Tractor Pre-Operation Inspection/Service8.2 Mower Pre-Operation Inspection/Service OPERATIONOPERATION OPERATIONOPERATION OPERATIONOPERATION 9. DRIVING THE TRACTOR AND MOWEROPERATION DANGEROPERATION 9.2 Brake and Differential Lock SettingOPERATION 9.1 Starting the TractorTransport Position OPERATIONOPERATION Transport Lock Braces9.4 Driving the Tractor and Mower OPERATIONOPERATION 9.5 Crossing Ditches and Steep Inclines OPERATIONOPERATION INCORRECT DO NOT approach ditch straight onOPERATION 10. OPERATING THE TRACTOR AND MOWEROPERATION 10.1 Foreign Debris HazardsOPERATION 10.2 Bystander/Passersby PrecautionsOPERATION STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UNLESSOPERATION 10.3 Engaging the Power Take Off PTOOPERATION 10.4 PTO RPM and Ground Speed10.5 Operating the Mower OPERATIONOPERATION DANGEROPERATION OPERATIONCorrect Mower Deck Positioning Wrong Mower Deck Positioning OPERATIONOPERATION 10.6 Shutting Down the Mower OPERATIONOPERATION OPERATION 11. DISCONNECTING THE MOWER FROM THE TRACTOROPERATION Driveline Storage BracketOPERATION 12. MOWER STORAGEOPERATION OPERATION 13. TRANSPORTING THE TRACTOR AND MOWEROPERATION DANGERTires and Wheels OPERATIONOPERATION 13.1 Transporting on Public Roadways OPERATIONOPERATION DANGEROPERATION OPERATION13.2 Hauling the Tractor and Mower OPERATIONOPERATION OPERATION 14. TROUBLE SHOOTING GUIDEOPERATION TROUBLEOPERATION TROUBLE SHOOTINGOPERATION TROUBLEOPERATION TROUBLE SHOOTINGOPERATION TROUBLEPage MAINTENANCE SECTION Maintenance SectionLUBRICATION INFORMATION MAINTENANCEMAINTENANCE DESCRIPTIONTONGUE FIGURE MAINTENANCEMAINTENANCE CENTER & WING GEARBOXESDIVIDER GEARBOX MAINTENANCEMAINTENANCE Do Not OperateMAIN CV DRIVELINE SAFETY SHIELD MAINTENANCEMAINTENANCE Figure 15 Remove the two shield bearings per half shaft by prying the head of the bearings up with a screwdriver, and pulling them out with pliers MAINTENANCEMAINTENANCE Figure 17 Grease the shield bearing grooves on the yokes and the inner telescoping member before assembly MAINTENANCEMAINTENANCE Figure 21 Attach safety decal as needed MAINTENANCEMAINTENANCE BLADE SERVICING MAINTENANCEMAINTENANCE DANGERBLADE SHARPENING MAINTENANCEMAINTENANCE BLADE REMOVALBLADE CARRIER INSTALLATION MAINTENANCEMAINTENANCE BLADE CARRIER REMOVALSEASONAL CLUTCH MAINTENANCE MAINTENANCEMAINTENANCE I J 1-9/16 - 1-15/32 minSTORAGE MAINTENANCEMAINTENANCE PROPER TORQUE FOR FASTENERSCaulking Gun w/Silicon MAINTENANCEMAINTENANCE Torque WrenchSTEP MAINTENANCEMAINTENANCE STEPSTEP MAINTENANCEMAINTENANCE STEPRemove all eight Bolts from Input Cap using a 14mm Socket. Then using a Hammer, tap the Output end of the Input Shaft. This will loosen the input Cap and allow the removal of the complete Input Shaft Assembly. FIGURE MAINTENANCEMAINTENANCE STEPAssembly of WW75-340 STEP MAINTENANCEMAINTENANCE Install the Bearing on the Output Shaft. FIGURE 33. Place the Shaft into the Hub Cap. FIGURE 34. Place the Bearing FIGURE 35on the Shaft and carefully drive it down FIGURE 36. Replace any shims found in disassembly, Place the Gear FIGURE 37on the Shaft so that the threads, for the Adjusting Nut, on Shaft are exposedSTEP MAINTENANCEMAINTENANCE STEP MAINTENANCEMAINTENANCE STEP MAINTENANCEMAINTENANCE STEPSTEP MAINTENANCEMAINTENANCE STEPSTEP MAINTENANCEMAINTENANCE 1 ITEM QTY DESCRIPTION MAINTENANCEMAINTENANCE RIGHT ANGLE GEARBOX OUTBOARD ASSEMBLY & DISASSEMBLY PROCEDURES MAINTENANCEMAINTENANCE OUTPUT SHAFT INSTALLATIONINPUT SHAFT REMOVAL MAINTENANCEMAINTENANCE 2. REMEDIES AND PROCEDURES SERVIS-RHINOLIMITED WARRANTY 1. LIMITED WARRANTIES RHINOPage REQUIRED OF THE OPERATOR WARRANTY LIMITATIONS - GEARBOXREQUIRED OF THE OWNER 1. Securely fasten seatbelt if the tractor has a ROPSPrinted U.S.A SR20ML-SOM-10/03P/N 00763403C 9907-60936 IL City, Gibson Ave Sangamon .S 00763505 .FILE ON IS CARD REGISTRATION WARRANTYRHINO-SERVIS Company Group Alamo AnCHECK AND ADJUST OR LUBRICATE AS REQUIRED SERVIS-RHINO WARRANTY REGISTRATION INFORMATIONPRE-DELIVERY SERVICE Page DEALER COPY SERVIS-RHINO WARRANTY REGISTRATION INFORMATIONPRE-DELIVERY SERVICE CHECK AND ADJUST OR LUBRICATE AS REQUIRED Page CUSTOMER COPY SERVIS-RHINO WARRANTY REGISTRATION INFORMATIONPRE-DELIVERY SERVICE CHECK AND ADJUST OR LUBRICATE AS REQUIRED