Manuals / Alamo / Lawn and Garden / Brush Cutter

Alamo SR14, SR20 manual Safety, Never unhitch without using the Tongue Jack. The Tongue is, Danger

Models: SR14 SR20

1 166

Download 166 pages 37.06 Kb

Page 17

Never unhitch without using the Tongue Jack. The Tongue is

(SGM-12)

(STI-6)

	SAFETY


WARNING!	Never unhitch without using the Tongue Jack. The Tongue is
	very heavy. Attempting to lift the Tongue without using the Tongue
	Jack could cause strains or other injury. Allowing the tongue to fall
	suddenly and unexpectedly could result in crushing injury. Use
	the Tongue Jack for lifting the mower only. Overloading the
	Tongue Jack can cause failure with possible serious bodily injury
	or even death. (STI-4)

SAFETY

CAUTION!

WARNING!

On a fully-assembled unit, do not remove the Wing Retaining Strap until hoses are attached to the tractor and the Wing Cylinders are filled with oil. Lower the Wings slowly and carefully. Keep bystand- ers away during operations. (STI-5)

Only tow the Implement behind a properly sized and equipped Tractor which exceeds the weight of the Implement by at least 20%. DO NOT tow the Implement behind a truck or other type of vehicle. Never tow the Implement and another Implement connected in tandem. Never tow the Implement at speeds over 20 MPH.

WARNING! Follow these guidelines to reduce the risk of equipment and grass fires while operating, servicing, and repairing the Mower and Tractor: -Equip the Tractor with a fire extinguisher in an accesible location.

-Do Not operate the Mower on a Tractor with an underframe exhaust. -Do Not smoke or have an open flame near the Mower and Tractor. -Do Not drive into burning debris or freshly burnt areas.

-Ensure slip clutches are properly adjusted to prevent excessive slippage and plate heating.

-Never allow clippings or debris to collect near drivelines, slip clutches, and gearboxes. Periodically shut down the Tractor and Mower and clean clippings and collected debris from the mower deck.

WARNING!

DANGER!

Do not mow with two machines in the same area except with Cab tractors with the windows closed.

(SGM-11)

Replace bent or broken blade with new blades. NEVER ATTEMPT TO STRAIGHTEN OR WELD ON BLADES SINCE THIS WILL LIKELY CRACK OR OTHERWISE DAMAGE THE BLADE WITH SUBSEQUENT FAILURE AND POSSIBLE SERIOUS INJURY FROM THROWN BLADES.

(SGM-10)

SR20M/SR14M 10/03

Safety Section 1-11

© 2004 Alamo Group Inc.

Image 17

Alamo SR14, SR20 manual Safety, Never unhitch without using the Tongue Jack. The Tongue is, or even death. STI-4, Danger

Contents

FLEX-WING MECHANICAL LEVEL LIFT ROTARY CUTTER / SHREDDER OPERATORS MANUALRHINO SR20/ SR14TO THE OWNER/OPERATOR/DEALER before operating the Mower Safety Training Makes the DifferenceBE SAFE BE ALERT BE ALIVE BE TRAINED Please Send Me SAFETY SECTION TABLE OF CONTENTSASSEMBLY SECTION MAINTENANCE SECTIONPage Safety Section SAFETY SECTIONSAFETY SAFETY¡LEA EL INSTRUCTIVO SAFETYSAFETY SAFETY SAFETYDANGER DANGER DANGER DANGER DANGERby the following rules SAFETYSAFETY SAFETY SAFETYDANGER KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglementSAFETY SAFETYDANGER DANGERSAFETY SAFETYDANGER QUENT FAILURE AND POSSIBLE SERIOUS INJURY FROM THROWNSAFETY SAFETYSTOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UNLESS DANGERSAFETY SAFETYDANGER DANGERSAFETY SAFETYNever unhitch without using the Tongue Jack. The Tongue is suddenly and unexpectedly could result in crushing injury. UseSAFETY SAFETYSEE YOUR SERVIS-RHINO DEALER SPRM-1SAFETY SAFETYSAFETY SAFETYLEVEL DESCRIPTIONSAFETY SAFETYSAFETY SAFETYSAFETY SAFETYSAFETY SR20 SR14SAFETY SAFETY SAFETY FEDERAL LAWS AND REGULATIONSEmployer-Employee Operator Regulations This Act SeeksPage Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section INTRODUCTION SECTIONINTRODUCTION INTRODUCTIONAssembly Section ASSEMBLY SECTIONBLADE CARRIER AND BLADES ASSEMBLYASSEMBLY ASSEMBLY ASSEMBLYLEVEL ROD ASSEMBLY TONGUE ATTACHMENTASSEMBLY ASSEMBLYWING SECTIONS ATTACHMENTS HOSE BRACKET ATTACHMENTASSEMBLY ASSEMBLYCENTER SECTION LEVEL LIFT AXLE ATTACHMENT FIGUREASSEMBLY ASSEMBLYAXLE ADJUSTMENT ROD ATTACHMENT CENTER AXLE HYDRAULIC CYLINDER ATTACHMENTASSEMBLY ASSEMBLYWING SECTION HYDRAULIC CYLINDER ATTACHMENT TIRES AND WHEELSASSEMBLY ASSEMBLYASSEMBLY ASSEMBLYBAFFLE KIT ASSEMBLY OPTIONAL SPRING STOP ATTACHMENTASSEMBLY ASSEMBLYASSEMBLY ASSEMBLYASSEMBLY ASSEMBLYDriveline Yoke 11/16 Bolt EndCANOPY SHIELDS ASSEMBLYASSEMBLY THREE SPOOL CONTROL VALVE INSTALLATION ASSEMBLYASSEMBLY Operation Section OPERATION SECTIONRHINO SR14/SR20 ROTARY MOWER OPERATION INSTRUCTIONS OPERATIONOPERATION OPERATION OPERATIONDANGER PELIGROOPERATION OPERATION Standard Equipment and SpecificationsSR20 SR14OPERATION 1. OPERATOR REQUIREMENTSOPERATION Personal Protective Equipment PPE2.2 Tractor Safety Devices 2. TRACTOR REQUIREMENTSOPERATION OPERATIONOPERATION Tractor Drawbar LengthOPERATION Based on Mower Operating Speed2.7 Power Take Off PTO 2.6 Front End WeightOPERATION OPERATIONOPERATION 3. GETTING ON AND OFF THE TRACTOROPERATION DANGEROPERATION 4. STARTING THE TRACTOROPERATION 5.1 Connecting the Mower Tongue to the Tractor OPERATION 5. CONNECTING THE MOWER TO THE TRACTORSafety Tow Chain OPERATIONOPERATION 5.2 Connecting Mower Hydraulic Lines to the TractorOPERATION Operating Mower Hydraulics with Three Tractor Hydraulic PortsSplit Collar Assemblies Leveling Rod Adjustments OPERATION 6. SETTING THE MOWERLeveling Rod Adjustments OPERATIONOPERATION 6.2 Setting Deck PitchOPERATION LEVELING WING SECTIONS WITH CENTEROPERATION 7. DRIVELINE ATTACHMENTOPERATION 7.1 Driveline Length CheckEngagement Check Procedure “Bottoming Out” Check ProcedureOPERATION OPERATIONOPERATION CV Driveline Maximum Angle Check ProcedureOPERATION 7.2 Constant Velocity CV DrivelineOPERATION 8. PRE-OPERATION INSPECTION AND SERVICEOPERATION DANGER8.2 Mower Pre-Operation Inspection/Service 8.1 Tractor Pre-Operation Inspection/ServiceOPERATION OPERATIONOPERATION OPERATIONOPERATION OPERATIONOPERATION 9. DRIVING THE TRACTOR AND MOWEROPERATION DANGEROPERATION 9.2 Brake and Differential Lock SettingOPERATION 9.1 Starting the TractorOPERATION OPERATIONTransport Position Transport Lock Braces9.4 Driving the Tractor and Mower OPERATIONOPERATION OPERATION OPERATION9.5 Crossing Ditches and Steep Inclines INCORRECT DO NOT approach ditch straight onOPERATION 10. OPERATING THE TRACTOR AND MOWEROPERATION 10.1 Foreign Debris HazardsOPERATION 10.2 Bystander/Passersby PrecautionsOPERATION STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UNLESSOPERATION 10.3 Engaging the Power Take Off PTOOPERATION 10.4 PTO RPM and Ground SpeedOPERATION OPERATION10.5 Operating the Mower DANGEROPERATION OPERATIONCorrect Mower Deck Positioning Wrong Mower Deck Positioning OPERATIONOPERATION 10.6 Shutting Down the Mower OPERATIONOPERATION OPERATION 11. DISCONNECTING THE MOWER FROM THE TRACTOROPERATION Driveline Storage BracketOPERATION 12. MOWER STORAGEOPERATION OPERATION 13. TRANSPORTING THE TRACTOR AND MOWEROPERATION DANGERTires and Wheels OPERATIONOPERATION OPERATION OPERATION13.1 Transporting on Public Roadways DANGEROPERATION OPERATION13.2 Hauling the Tractor and Mower OPERATIONOPERATION OPERATION 14. TROUBLE SHOOTING GUIDEOPERATION TROUBLEOPERATION TROUBLE SHOOTINGOPERATION TROUBLEOPERATION TROUBLE SHOOTINGOPERATION TROUBLEPage Maintenance Section MAINTENANCE SECTIONMAINTENANCE MAINTENANCELUBRICATION INFORMATION DESCRIPTIONMAINTENANCE MAINTENANCETONGUE FIGURE CENTER & WING GEARBOXESMAINTENANCE MAINTENANCEDIVIDER GEARBOX Do Not OperateMAIN CV DRIVELINE SAFETY SHIELD MAINTENANCEMAINTENANCE Figure 15 Remove the two shield bearings per half shaft by prying the head of the bearings up with a screwdriver, and pulling them out with pliers MAINTENANCEMAINTENANCE Figure 17 Grease the shield bearing grooves on the yokes and the inner telescoping member before assembly MAINTENANCEMAINTENANCE Figure 21 Attach safety decal as needed MAINTENANCEMAINTENANCE MAINTENANCE MAINTENANCEBLADE SERVICING DANGERMAINTENANCE MAINTENANCEBLADE SHARPENING BLADE REMOVALMAINTENANCE MAINTENANCEBLADE CARRIER INSTALLATION BLADE CARRIER REMOVALMAINTENANCE MAINTENANCESEASONAL CLUTCH MAINTENANCE I J 1-9/16 - 1-15/32 minMAINTENANCE MAINTENANCESTORAGE PROPER TORQUE FOR FASTENERSMAINTENANCE MAINTENANCECaulking Gun w/Silicon Torque WrenchMAINTENANCE MAINTENANCESTEP STEPMAINTENANCE MAINTENANCESTEP STEPMAINTENANCE MAINTENANCERemove all eight Bolts from Input Cap using a 14mm Socket. Then using a Hammer, tap the Output end of the Input Shaft. This will loosen the input Cap and allow the removal of the complete Input Shaft Assembly. FIGURE STEPMAINTENANCE MAINTENANCEAssembly of WW75-340 STEP Install the Bearing on the Output Shaft. FIGURE 33. Place the Shaft into the Hub Cap. FIGURE 34. Place the Bearing FIGURE 35on the Shaft and carefully drive it down FIGURE 36. Replace any shims found in disassembly, Place the Gear FIGURE 37on the Shaft so that the threads, for the Adjusting Nut, on Shaft are exposedSTEP MAINTENANCEMAINTENANCE STEP MAINTENANCEMAINTENANCE MAINTENANCE MAINTENANCESTEP STEPMAINTENANCE MAINTENANCESTEP STEPSTEP MAINTENANCEMAINTENANCE 1 ITEM QTY DESCRIPTION MAINTENANCEMAINTENANCE MAINTENANCE MAINTENANCERIGHT ANGLE GEARBOX OUTBOARD ASSEMBLY & DISASSEMBLY PROCEDURES OUTPUT SHAFT INSTALLATIONINPUT SHAFT REMOVAL MAINTENANCEMAINTENANCE LIMITED WARRANTY 1. LIMITED WARRANTIES SERVIS-RHINO2. REMEDIES AND PROCEDURES RHINOPage REQUIRED OF THE OWNER WARRANTY LIMITATIONS - GEARBOXREQUIRED OF THE OPERATOR 1. Securely fasten seatbelt if the tractor has a ROPSPrinted U.S.A SR20ML-SOM-10/03P/N 00763403C RHINO-SERVIS 00763505 .FILE ON IS CARD REGISTRATION WARRANTY9907-60936 IL City, Gibson Ave Sangamon .S Company Group Alamo AnCHECK AND ADJUST OR LUBRICATE AS REQUIRED SERVIS-RHINO WARRANTY REGISTRATION INFORMATIONPRE-DELIVERY SERVICE Page DEALER COPY SERVIS-RHINO WARRANTY REGISTRATION INFORMATIONPRE-DELIVERY SERVICE CHECK AND ADJUST OR LUBRICATE AS REQUIRED Page CUSTOMER COPY SERVIS-RHINO WARRANTY REGISTRATION INFORMATIONPRE-DELIVERY SERVICE CHECK AND ADJUST OR LUBRICATE AS REQUIRED