Manuals / Brands / Laundry Appliance / Washer / Alliance Laundry Systems / Laundry Appliance / Washer

Alliance Laundry Systems PHM798N, PHM802N Chemical injection Using External AC Power Source

1 61

Download 61 pages, 2.61 Mb

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Specifications and Dimensions

57

F8138601

Chemical injection Using External AC Power Source

NOTE: An External AC Power Source is NOT

provided by Alliance Laundry Systems.

NOTE: Power for external supplies must not be

derived from the high-voltage main power

connection point.

IMPORTANT: The external power must supply

power of 240VAC or less and be protected at 3

Amps or less.

1. Remove the red jumper wire installed by the

factory between “24VAC”: and “RELAY COM”.

2. Connect one side of the external power to the

“RELAY COM” and the other to the external

dispenser input signals common. Refer to

Figure32.

Figure 32

PHM823N

1External Supply Power 4VAC Power Terminal

2Red Jumper Wire 5VAC RETURN Terminal

3External Supply Common

= Power

= Neutral

1

2

3

5

4

Do not attempt to increase fuse rating or

alter wiring of external chemical supply

terminal strip in such as way that may

conflict with the suggested methods

provided on the Optional External Supply

Wiring Diagram.

W699

CAUTION

Contents

Main Installation www.comlaundry.com Washer-Extractors (If this machine changes ownership, this manual must accompany machine.) Pocket Hardmount UniLinc and M30 Control Refer to Page 8 for Model Numbers Page Table of Contents Safety Information Explanation of Safety Messages Important Safety Instructions DANGER Page Safety Decals Operator Safety Safe Operating Environment Environmental Conditions Machine Location DANGER Input and Output Services AC Inverter Drive Introduction Model Identification Information in this manual is applicable to these models: Delivery Inspection Name plate Location Nameplate Location - UniLinc Models Replacement Parts Customer Service Page Specifications and Dimensions UWTV Models Through 3/31/09 * Basket Only Overall Dimensions Weight And Shipping Information 12 UWTV Models Through 3/31/09 (Continued) Cylinder Speeds / Centrifugal Force Data Balance Detection Direct Steam Heating (Optional) 13 UWL, UWN and UWU Models Starting 4/1/09 Specifications 35 60 80 100 125 150 Overall Dimensions * Basket Only Weight And Shipping Information Wash Cylinder Information 14 UWL, UWN and UWU Models Starting 4/1/09 (Continued) Cylinder Speeds / Centrifugal Force Data Balance Detection Direct Steam Heating (Optional) Machine Dimensions Dimensional Clearances UWTV Models Through 3/31/09 Crush hazard. (Refer to Figure 3 and Figure 4) 16 Figure 3 17 Figure 4 UW Design 1 and Design 2 Models Starting 4/1/09 Through 10/3/10 (Refer to Figure 5 and Figure 6) 19 Figure 5 20 Figure 6 UW Design 3 Models starting 10/4/10 (Refer to Figure 7 and Figure 8) 22 Figure 7 23 Figure 8 Machine Foundation Requirements Concrete Foundation Pad Installation Page Floor Load Data Static and dynamic loads on the floor or foundation are shown in Tabl e 4 and Table 5. Page Page Mounting Bolt Installation Requirements Machine Mounting and Grouting 32 Mounting Bolt Hole Locations AA Figure 12 NOTE: Mounting holes marked A are on V-speed Models only. 35 MODEL 33 Figure 13 60 VARIABLE-SPEED MODEL 34 Figure 14 80 / 100 MODELS 35 Figure 15 125 MODEL F8138601 36 Figure 16 150 MODEL 37 Grout Placement 125 MODEL 60 2-SPEED MODEL 100 MODEL 80 MODEL Gap Setting for Vibration Switch For UniLinc Models, Navigate to the Inputs Outputs Menu: Verify Vibration Switch Gap (for 35-125 Pound Models): Verify Vibration Switch Gap (For 150 Pound Design 1 Models): Verify Safety Switch Operation (For 150 Pound Design 2 Models): 35 Pound Model 60, 80, 100 and 125 Pound Models Page Drain Connection Requirements Page Water Connection Page Electrical Installation Requirements Page Page Page ** M30 Control Models only. Steam Requirements (Steam Heat Option Only) Chemical Injection Supply System Undiluted chemical dripping can damage the washer- Connecting External Liquid Supplies to the Washer-Extractor IMPORTANT: Do not attach anything to nozzles. Air gap must be maintained. External Supplies Chemical Injection Using Internal 24VAC Control Transformer Chemical injection Using External AC Power Source External Supply Signals