Manuals / AMX / Computer Equipment / Network Card

AMX manual Introduction, NI-2100, NI-3100, NI-4100 Hardware Reference Guide

Models: NI-2100 NI-3100 NI-4100

1 36

Page 16

Introduction

12	NI-2100, NI-3100, NI-4100 Hardware Reference Guide

Page 16

Image 16

AMX manual Introduction, NI-2100, NI-3100, NI-4100 Hardware Reference Guide

Contents

NI-x100 Series Hardware Reference GuideNetLinx Integrated Controllers NI-2100, NI-3100, NI-4100 NetLinx Integrated ControllersAMX Limited Warranty and Disclaimer Table of Contents Installation and UpgradingConnections and Wiring IntroductionInput/Output I/O Port Connections and Wiring IR/Serial Port Connections and WiringNetLinx Control Card Slot Connector NI-4100 only Ethernet/RJ-45 Port Connections and WiringIntroduction NetLinx Integrated Master Controller FeaturesNI-2100 Specifications NI-2100 Specifications IntroductionNote AMX may increase Flash size at any time in response to Flash size providedNI-2100 Specifications Cont SettingsIntroduction Rear Panel Components ContFIG. 4 NI-3100 front and rear panel connectors and components NI-3100 SpecificationsFIG. 3 NI-3100 NetLinx Integrated Controller front view NI-3100 Specifications IntroductionFront Panel LEDs Rear Panel ComponentsNI-3100 Specifications Cont SettingsIntroduction Rear Panel Components ContNI-4100 Specifications 8 IR/Serial Output ports, 8 Digital Input/Output ports, and 8 RelaysIntroduction FrontNI-4100 Specifications IntroductionFront Panel LEDs/Slots Rear Panel ComponentsNI-4100 Specifications Cont SettingsIntroduction Rear Panel Components ContIntroduction Related DocumentsNI-2100, NI-3100, NI-4100 Hardware Reference Guide Introduction NI-2100, NI-3100, NI-4100 Hardware Reference GuideInstallation and Upgrading Installing NetLinx Control Cards NI-4100 OnlySetting the NetLinx Control Card Addresses NI-4100 Only DevicePortSystem DPSCompact Flash Upgrades Removing NetLinx Control Cards NI-4100 OnlyAccessing The Internal Components On An Integrated Controller The NI-4100 has six screws on top and four on each sideInstallation of Compact Flash Upgrades 5. Remove the upgrade card from it’s anti-static bagInstalling Into An Equipment Rack Closing and Securing the Outer Housing7. Apply power to the unit to complete the installation Connections and Wiring Setting the Configuration DIP Switch for the Program PortBaud Rate Settings Program Run Disable PRD ModeProgram Port Connections and Wiring Setting the CardFrame DIP Switch NI-4100 OnlyWorking With the Configuration DIP Switch Modes and Front Panel LED Blink Patterns Port Assignments and FunctionalityConnections and Wiring Modes and LED Blink PatternsWiring Guidelines AXlink Port and LEDWiring length guidelines 1 blink per second - Normal operationPreparing Captive Wires 1. Strip 0.25 inch 6.35 mm of insulation off all wiresWiring a Power Connection Using the 4-Pin Mini-Phoenix Connector For Data and PowerDB9 Device Port Connections and Wiring Using the 4-pin Mini-Phoenix Connector For Data With External PowerICSNet Port Connections and Wiring RS-232/422/485 Device Port Wiring SpecificationsICSNet RJ-45 Signals Connections and WiringRelay Port Connections and Wiring ICSHub OUT Port Connections and WiringRelay Connections Input/Output I/O Port Connections and Wiring IR/Serial Port Connections and Wiring NetLinx Control Card Slot Connector NI-4100 onlyEthernet/RJ-45 Port Connections and Wiring Ethernet LEDsConnections and Wiring Ethernet Ports Used By the Integrated ControllerEthernet Port Descriptions Port typeConnections and Wiring NI-2100, NI-3100, NI-4100 Hardware Reference GuideIt’s Your World - Take Control