AMX NI-2100 manual NI-4100 Specifications Cont, Introduction, Rear Panel Components Cont, Settings

Models: NI-2100 NI-3100 NI-4100

1 36
Download 36 pages 4.69 Kb
Page 14
Image 14
NI-4100 Specifications (Cont.)

Introduction

NI-4100 Specifications (Cont.)

Rear Panel Components (Cont.):

• Program Port:

RS-232 DB9 connector (male) can be connected to a DB9 port on a PC.

 

This connector can be used with serial and NetLinx programming com-

 

mands, as well as other DB9 capable devices, to both upload/download

 

information from the NetLinx Studio program.

 

 

• Configuration DIPSwitch:

Sets the communication parameters for the Program port (see Baud Rate

 

Settings).

 

 

• ID Pushbutton:

Sets the NetLinx ID (Device only) assignment for the device.

• Ethernet Port:

RJ-45 connector provides TCP/IP communication. This is an Auto MDI/

 

MDI-X enabled port, which allows you to use either straight-through or

 

crossover Ethernet cables.

 

The Ethernet Port LEDs show communication activity, connection status,

 

speeds, and mode information:

 

SPD (speed) - Yellow LED lights On when the connection speed is 100

 

Mbps and turns Off when the speed is 10 Mbps.

 

L/A (link/activity) - Green LED lights On when the Ethernet cables are

 

connected and terminated correctly, and blinks when receiving Ethernet

 

data packets.

 

 

• AxLink Port:

4-pin 3.5 mm mini-Phoenix (male) connector that provides data and power

 

to external control devices. Green AXlink LED indicates the state of the

 

AXlink port.

 

 

• Power Port:

2-pin 3.5 mm mini-Phoenix (male) connector.

• CardFrame #DIP Switch:

Sets the starting address for the Control Cards in the CardFrame. (Factory

 

default CardFrame DIP switch value = 0). The Control Card address range

 

is 1-3064.

 

 

• Control Card Connectors (1-4):

20-pin (male) connectors that connect the Control Cards and

 

external equipment to the CardFrame.

 

 

Included Accessories:

2-pin 3.5 mm mini-Phoenix (female) PWR connector (41-5025)

 

4-pin 3.5 mm mini-Phoenix (female) AXlink connector (41-5047)

 

10-pin 3.5 mm mini-Phoenix (female) I/O connector (41-5107)

 

• Installation Kit (KA2105-01):

 

- 8-pin Relay Common Strip

 

- 4 rack mount screws

 

- 4 washers

 

• 2 8-pin 3.5 mm mini-Phoenix (female) Relay connectors

 

(41-5083)

 

• 2 CC-NIRC NetLinx IR Emitter Cables (FG10-000-11)

 

• 2 removable rack ears (62-2105-07)

 

 

Other AMX Equipment:

2-pin 3.5 mm mini-Phoenix male connector (41-5026)

 

• CSB Cable Support Bracket (FG517)

 

CC-NSER IR/Serial cables (FG10-007-10)

 

• NCK, NetLinx Connector Kit (FG2902)

 

• STS, Serial To Screw Terminal (FG959)

 

• Upgrade Compact Flash (factory programmed with firmware):

 

NXA-CF2NI256M - 256 MB compact flash card (FG2116-47)

 

NXA-CF2NI512M - 512 MB compact flash card (FG2116-48)

 

NXA-CF2NI1G - 1 GB compact flash card (FG2116-49)

 

 

10

NI-2100, NI-3100, NI-4100 Hardware Reference Guide

Page 14
Image 14
AMX NI-2100, NI-3100 manual NI-4100 Specifications Cont, Introduction, Rear Panel Components Cont, Settings