Off | Analog Devices ADSP-21369 specification

EZ-KIT Lite Hardware Reference

Figure 2-4. Switch Locations and Default Settings

Table 2-3. Boot Mode Configuration Switch (SW2)

BOOTCFG1 Pin (Position 1)	BOOTCFG0 Pin (Position 2)	Boot Mode


ON	ON	SPI Slave Boot

ON	OFF	Flash Boot1
OFF	ON	SPI Master Boot

OFF	OFF	Reserved

1 Bold typeface denotes the default setting.

ADSP-21369 EZ-KIT Lite Evaluation System Manual

2-9

Image 47

Analog Devices ADSP-21369 system manual Off

Contents

ADSP-21369 EZ-KIT Lite Evaluation System Manual Disclaimer Limited WarrantyTrademark and Service Mark Notice Copyright Information Regulatory Compliance Page Contents Using EZ-KIT Lite ADSP-21369 EZ-KIT Lite Evaluation System Manual Vii Bill of Materials Schematics Index Preface Page Preface Page Intended Audience Manual ContentsPurpose of This Manual What’s New in This Manual What’s New in This ManualTechnical or Customer Support Product Information Supported Processors Product Information MyAnalog.comProcessor Product Information Title Description Related Documents Each documentation file type is described as follows Online Technical Documentation Accessing Documentation From Web Accessing Documentation From VisualDSP++Accessing Documentation From Windows Processor Manuals Printed ManualsVisualDSP++ Documentation Set Hardware Tools Manuals Preface Data Sheets Notation Conventions Notation Conventions Preface Xxiv ADSP-21369 EZ-KIT Lite Evaluation System Manual Using EZ-KIT Lite Package Contents Using EZ-KIT Lite Default Configuration Installation and Session Startup Installation and Session Startup Using EZ-KIT Lite Evaluation License Restrictions Evaluation License Restrictions External Memory Start Address End Address Content Elvis Interface Elvis Interface Analog Audio LEDs and Push Buttons LEDs and Push Buttons PB1 SW8 FLAG1/~IRQ1 PB2 Example Programs Example ProgramsBackground Telemetry Channel Sors/resources/crosscore/emulators/index.html. For more Background Telemetry Channel EZ-KIT Lite Hardware Reference System Architecture System Architecture EZ-KIT Lite Hardware Reference External Port DAI Interface ADSP-21369 DPI Interface Flag Pins Expansion Interface External PLL Jtag Emulation Port Switch SettingsBoot Mode and Clock Ratio Select Switch SW2 Switch Settings OFF Core Clock Rate Configuration Codec Setup Switch SW3 Uart Enable Switch SW5 Electret Microphone Select Switch SW4 Push Button Enable Switch SW7 Loop-Back Test Switches SW6 and SW14 Elvis Function Generator Configuration Switch SW13 Elvis Oscilloscope Configuration Switch SW1 General Purpose LEDs LED1-8 Power LED LED9 LED and Push Button Locations Reset LEDs LED10 and LED12 Push Buttons SW8-11 USB Monitor LED LED11 VCO Select Jumper JP1 Board Reset Push Button SW12Jumpers Jumper Locations 10. VCO Select Jumper JP1 Jumpers Elvis Voltage Selection Jumper JP3 Elvis Select Jumper JP2 Elvis Programmable Flag Jumper JP4 ConnectorsExpansion Interface Connectors J1-J3 Connectors Connector Locations Headphone Out Jack P7 Audio In RCA Connector P10Audio Out RCA Connector J5 Power Jack J4 Spdif Coax Connectors P8 and P9 RS-232 Connector P1 DAI Header P4 USB Connector P5DPI Header P3 Jtag Header P2 Connectors Bill of Materials Description Reference Designator Manufacturer Part Number Bill Of Materials VR5 ADI Switchcraft PJRAN1X1U01 BLK SPST-MOMENTARY SWT013 2A S2ARECT DO-214AA Panasonic ERJ-2GEJ472X DIGI-KEY P1.5KCFCT-ND Yageo ERJ-3RSFR10V Panasonic ECJ-1VC1H101J RED-SMT LED001 LED10,LED12 Panasonic ADSP-21369 EZ-KIT Lite Evaluation System Manual ADSP-21369 EZ-KIT Lite Schematic Devices DSP Memory Analog Audio Audio OUT DAC3 Left Audio in & Headphone OUT Analog DSP IO Current PUSHBUTTONS, LEDS, & Reset Expansion Interface Power Index Index Jtag SPI