Begin initial configuration | ATTO Technology FastStream VT, 5300

•The switch(es) allows UDP broadcast messages to be passed through.

•A router is not placed between the host running QuickNav and the FastStream VT 5300.

•You have connected the FastStream VT 5300 and the network using at least Cat5e cabling.

•You have noted the FastStream VT 5300 serial number from the bottom of the unit.

Note

The FastStream VT 5300 is initially configured with DHCP enabled. It is best if you have access to a DHCP server.

1Work from the computer attached to the FastStream VT 5300 Ethernet port on the same broadcast domain. From the CD supplied with your FastStream, run the QuickNav Utility QuickNAV-windows.exefor Windows or QuickNAV-Macfor Mac OS X.

2Locate the FastStream with the serial number recorded earlier.

3Highlight the serial number.

4Click Next.

If a DHCP server is available on your network, an address is assigned automatically by the server. Note the assigned address:

_________________________________

____

If you do not have a DHCP server, get an IPaddress and subnet mask from your network administrator, type it into the area provided, and select Next.

5Click on Launch Browser

Your browser points to the FastStream VT 5300 splash screen.

Begin initial configuration

1The FastStream GUI welcome screen appears. Click on Enter Here

2Type in the username and password.

Note

The default username is root; it is case insensitive. The default password is Password; it is case sensitive. It is best practice to change the passwords. Refer to Optional changes to system parameters on page 11.

3The Initial Setup page appears.

Before creating a Virtual Tape Library, you may wish to initialize and verify your drives to ensure drive integrity. Refer to Initialize and verify drives on page 17.

CAUTION

Selecting Drive Initialization causes all previous storage data on the drive to be erased. Make sure all of your information is backed up before initializing drives.

4Go on to Configure Virtual Tape on page 7.

Exhibit 2.0-1 General bracket assembly.

6

Image 11

ATTO Technology FastStream VT, 5300 operation manual Begin initial configuration, Click on Launch Browser

Contents

FastStream VT Page Page Contents Interface options Update storage and firmwareAppendix E Warranty, contact information Xxi Modify storage Management and control features Hardware featuresVirtual Tape features Backup and restore features GbE network Gb FC Switch GbE SwitchEthernet Fibre Channel Physical attributes Installation Install Windows drivers InstallationUnpack the packing box verify contents Install the FastStream Click on Launch Browser Begin initial configuration Configure Virtual Tape Use custom initial setup Use quick initial configuration Click on the Add/Remove Hot Spares button Use Hot Spare devices Move Virtual Tape Cartridges Click in the Enable/Disable Write Protection buttonEnable/Disable Write Protection page appears Secure data through Write Protection Optional changes to system parameters Customize the username, passwordChange system configurations Advanced CLI Changes to other parameters may be made using the Advanced Monitor VTL Monitor storage and diagnose configurations Phone home E-mail messages Configuration DisplayHealth and Status Monitor Measure drive performance Click the Set up Error Notification buttonConfiguration Select Verify Only Scan drive surfacesVerify storage Click the Initialize and Verify button Add drives to a RAID Group Modify storageInitialize and verify drives Select the Add/Remove Hot Spares button Rebuild RAID GroupsAdd or remove Hot Spares Select Rebuild RAID Groups Click in the Delete Virtual Tape Library button Add a VTL from another FastStream VTLDelete a VTL Move Virtual Tape Cartridges Preliminary steps Update storage and firmwareRemove stale VTL configuration data Update firmware Click Send File Use FTP over EthernetUse the RS-232 serial link Send File Type FastStream VT 5300 in the New Connection dialog box Interface optionsUse the serial port Enter Use Telnet Cable types Appendix a CablingScsi cabling Cable length Fibre Channel connections Disk Appendix B Designing RAID groupsJbod Just a Bunch of Disks RAID Level Iv Appendix Appendix C CLI provides an ASCII-based interface Symbol Indicates Mp1 CLI error messages CLI summary Command Default Example Viii Appendix Sntp CLI command explanations DumpConfig DefaultInterleaveDHCPFixedDelay DriveTestConfig EmailUsername EmailPasswordEmailNotifyAddress EmailServerAddress FCHardAddress FCPortErrorsFCDataRate FCHard IsReserved PasswordIPGateway IPSubnetMask RGCancelAddStorage RAIDCommandTimeoutResetFCPortErrors RestoreConfiguration RGHaltRebuild RGWaitTimeoutRGDisplay RGHaltConversion RMStatus SaveConfigurationSCSIPortReset SCSIPortResetOnStartup TailEventLog SerialPortBaudRateSerialPortEcho SNTPServer This equipment generates, uses, and can radiate radio Further results of FCC TestingAppendix D Standards and compliances Declaration of Conformity European Standards Contact Atto Technology, Inc Appendix E Warranty, contact informationManufacturer limited warranty Xxii Appendix