Operation, Safety recommendation | Avery ALS 330/430 manual

Operators Manual

ALS 330/430

4. Operation

This chapter describes the operation of the machine.

4.1 Safety recommendation

CAUTION!

y Before connections to the mains check the correct voltage selection.

yUse only original spare parts for service.

yOpen of the cover is only allowed authorised personal.

yHandling of the machine is permitted only trained personal.

yBe careful on operation, fingers, hair, clothes, jewellery, etc. may be caught by and get into rotating axles.

Release 4/06

Page 23

Operation

Image 25

Avery ALS 330/430 manual Operation, Safety recommendation

Contents

Page Page ALS 330/430 Menu structure Errors and warnings ALS 330/430 Overview Important NotesManufacturer Copyright General Safety Notes Safety Operator’s duty of care Concrete security regulations and symbols used Security measures during normal operation Security measures during maintenance and repairs Work on pneumatic equipment Work on the electrical equipmentObserve environmental regulations Mechanics Description Machine layout Operator panel Operator panel Plug board Plug board Electronics ALS 330/430 Preparing the machine InstallationPrepare dispensing Define label data Manual adjustment of the Cont parameter Setting Lpit manually Capacitive sensor Capacitive label sensor Label guide Adjust dispense functionStop position Automatic dispensing speed Apsf Fixed dispensing speedLabel position on the product Product data bank Operation Safety recommendation Left hand version Right hand version Inserting label material Mounting a new label roll Removing label material Mounting a new label roll on ALS Mounting a new label roll on ALS 330 Euro Rewind Adjusting the pressure roller Adjustment of the dispensing edge Lead screw adjustmentPrinter adjustment Initializing new label material Adjust pressure roller Control of dispense unit Function Display message Mains switchDispenser Menu selection Missing label function and web breaks Dispenser active on Display and data inputDisplay Menu function Function data value Material initialisation Init Dispenser stopped OFFLabel position POS Stop position Stod Start delaySTADDispense speed Velo Blow on time Blow MaintenanceProduct menu PD0n Release 4/06 Operation Page Menu structure Configuration menuStandard menu Extended standard menu Standard menu Direct ConfigurationApplicator Extended menu Initialisation Init Standard menuDisplay Function Values Labelling time Blow Start delay StadDispensing speed Velo Display Function Data value Extended standard menu Label contrast Label pitch LpitSensor status Sens Label positionPOS Product length Prdl Egra value check Stst Electronic gear ratio adjustment EgraSlew speed Slew Dwell time APT1 Blow on time APT2 Restart delay APT3Time constant compensation APT4 Printer dwell time PDT End of air stream signal AstpSave parameter in data bank Save Load data bank Load Product menu Page Possible adjustments Configuration menuCalling the configuration menu Possible tests Display Function of the parameter Possible data entry Handling the menu Menu functions Type of applicator Appl Automatic product speed followerAPSF Output check OCH Input and sensor check ICHAdditional functions in the standard menu Interface baud rate Baud Adjustment resettingFACTParity bit Pari Number of stop bits Sbit Recycle simulates max labels/min Recy Number of data bits DbitDistance sensor to dispensing edge Dist Label counter Labc Leave Menu finishing Quit Serial interface Dispenser connector Signal description Pol DData of the serial interface Direction Code Description 25 pol Pol Sub Command Description Range Interface commandsExample Ledg Message in display Output signals Connections and signals Applicator modes Signals for direct dispense Timing ASA applicator Control signals for the ASA applicator APT2 Signals for the EP applicator Applicator connector Applicator connector Connecting NPN left or PNP right inputs Input signals Product sensor Example for connecting an NPN sensor Datalogic NPN connection of optional ODC sensor OD Control sensor Connection of a NPN type Apsf sensor Apsf sensor Optional connector for process contro Control signals Internal I/O connector Rule EMI Electronic diagrams Wiring diagram Layout dispenser electronic board Resolution ALS 330/430 Page Dispenser error messages Errors and warningsSTO! Power-fail message Message Meaning How to solve Into Eeprom Dispenser warnings ALS 330/430 Technical Information Technical specificationDescription Details 330 430 APSF- Sensor Specification Optional function Application specification Charts Performance charts Performance chart Ramp Norm Deceleration Labels/min 900 25 mm 50 mm 75 mm 800 ALS 330/430 Page Function Factory Application Adjustment Function PD05 PD06 PD07 PD08 PD09 Function Factory PD01 PD02 PD03 PD04 Index