Plug board | Avery ALS 330/430 instruction

Operators Manual

ALS 330/430

ENTER: This key is used to enter or exit a menu point or to cancel a warning or error message.

When the keys have different meanings, it will be explained in the relevant menu description.

2.3 Plug board

The plug board is shown in Figure 3. Beside the mains switch and the mains cable socket there are some more holes for optional functions. Standard execution in this machine is one I/O plug prepared for the product sensor. The connection of the other plugs is described in chapter Connections.

If you use the optional connections, it is strongly recommended to do this by means of the optional available SUB-D connectors. This ensures best EMI stability of the machine.

APSF-Sensor

Product

Applicator

SPS control

Figure 3 Plug board

The fuse holder setting you have to select according to your local main voltage (100, 120, 220 or 240 V). You carry this out by taking off the fuse holder and position the fuse holder insert accordingly.

Release 4/06

Page 14

Description

Image 16

Avery ALS 330/430 manual Plug board

Contents

Page Page ALS 330/430 Menu structure Errors and warnings ALS 330/430 Important Notes OverviewManufacturer Copyright Safety General Safety Notes Operator’s duty of care Concrete security regulations and symbols used Security measures during maintenance and repairs Security measures during normal operation Work on pneumatic equipment Work on the electrical equipmentObserve environmental regulations Description Mechanics Machine layout Operator panel Operator panel Plug board Plug board Electronics ALS 330/430 Preparing the machine InstallationPrepare dispensing Define label data Setting Lpit manually Manual adjustment of the Cont parameter Capacitive label sensor Capacitive sensor Label guide Adjust dispense functionStop position Fixed dispensing speed Automatic dispensing speed ApsfLabel position on the product Product data bank Safety recommendation Operation Inserting label material Left hand version Right hand version Removing label material Mounting a new label roll Mounting a new label roll on ALS 330 Euro Mounting a new label roll on ALS Adjusting the pressure roller Rewind Adjustment of the dispensing edge Lead screw adjustmentPrinter adjustment Adjust pressure roller Initializing new label material Function Display message Mains switch Control of dispense unitDispenser Menu selection Missing label function and web breaks Dispenser active on Display and data inputDisplay Menu function Function data value Material initialisation Init Dispenser stopped OFFLabel position POS Stop position Stod Start delaySTADDispense speed Velo Blow on time Blow MaintenanceProduct menu PD0n Release 4/06 Operation Page Configuration menu Menu structureStandard menu Extended standard menu Configuration Standard menu DirectApplicator Extended menu Initialisation Init Standard menuDisplay Function Values Labelling time Blow Start delay StadDispensing speed Velo Extended standard menu Display Function Data value Label contrast Label pitch LpitSensor status Sens Product length Prdl Label positionPOS Electronic gear ratio adjustment Egra Egra value check StstSlew speed Slew Dwell time APT1 Blow on time APT2 Restart delay APT3Time constant compensation APT4 End of air stream signal Astp Printer dwell time PDTSave parameter in data bank Save Load data bank Load Product menu Page Configuration menu Possible adjustmentsCalling the configuration menu Possible tests Handling the menu Display Function of the parameter Possible data entry Menu functions Automatic product speed followerAPSF Type of applicator Appl Output check OCH Input and sensor check ICHAdditional functions in the standard menu Adjustment resettingFACT Interface baud rate BaudParity bit Pari Number of stop bits Sbit Number of data bits Dbit Recycle simulates max labels/min RecyDistance sensor to dispensing edge Dist Label counter Labc Leave Menu finishing Quit Dispenser connector Signal description Pol D Serial interfaceData of the serial interface Direction Code Description 25 pol Pol Sub Command Description Range Interface commandsExample Ledg Message in display Connections and signals Output signals Signals for direct dispense Applicator modes Control signals for the ASA applicator Timing ASA applicator Signals for the EP applicator APT2 Applicator connector Applicator connector Input signals Connecting NPN left or PNP right inputs Example for connecting an NPN sensor Datalogic Product sensor OD Control sensor NPN connection of optional ODC sensor Apsf sensor Connection of a NPN type Apsf sensor Control signals Optional connector for process contro Internal I/O connector EMI Rule Electronic diagrams Wiring diagram Layout dispenser electronic board Resolution ALS 330/430 Page Errors and warnings Dispenser error messagesSTO! Power-fail message Message Meaning How to solve Into Dispenser warnings Eeprom ALS 330/430 Technical Information Technical specificationDescription Details 330 430 Application specification APSF- Sensor Specification Optional function Performance charts Charts Performance chart Ramp Norm Deceleration Labels/min 900 25 mm 50 mm 75 mm 800 ALS 330/430 Page Adjustment Function Factory Application Function Factory PD01 PD02 PD03 PD04 Function PD05 PD06 PD07 PD08 PD09 Index