Adjusting the pressure roller, Rewind | Avery ALS 330/430 guide

Operators Manual

ALS 330/430

the backing material is clamped in the slot. Wind the mandrel a few times to take up any backing material slack between the deviator roller and the rewind mandrel.

Figure 11 Rewind

4.2.3Adjusting the pressure roller

The pressure roller should always be positioned over the middle of the backing material. This ensures accurate label placement. Turn the pressure roller away from the drive roller. Loosen both knurled screws. Move the entire unit to its correct position. Fasten the screws securely again.

Figure 12 Pressure roller

Release 4/06

Page 27

Operation

Image 29

Avery ALS 330/430 manual Adjusting the pressure roller, Rewind

Contents

Page Page ALS 330/430 Menu structure Errors and warnings ALS 330/430 Overview Important NotesManufacturer Copyright General Safety Notes Safety Operator’s duty of care Concrete security regulations and symbols used Security measures during normal operation Security measures during maintenance and repairs Observe environmental regulations Work on the electrical equipmentWork on pneumatic equipment Mechanics Description Machine layout Operator panel Operator panel Plug board Plug board Electronics ALS 330/430 Prepare dispensing InstallationPreparing the machine Define label data Manual adjustment of the Cont parameter Setting Lpit manually Capacitive sensor Capacitive label sensor Stop position Adjust dispense functionLabel guide Automatic dispensing speed Apsf Fixed dispensing speedLabel position on the product Product data bank Operation Safety recommendation Left hand version Right hand version Inserting label material Mounting a new label roll Removing label material Mounting a new label roll on ALS Mounting a new label roll on ALS 330 Euro Rewind Adjusting the pressure roller Printer adjustment Lead screw adjustmentAdjustment of the dispensing edge Initializing new label material Adjust pressure roller Control of dispense unit Function Display message Mains switchDispenser Menu selection Missing label function and web breaks Display Menu function Function data value Display and data inputDispenser active on Label position POS Dispenser stopped OFFMaterial initialisation Init Dispense speed Velo Start delaySTADStop position Stod Product menu PD0n MaintenanceBlow on time Blow Release 4/06 Operation Page Menu structure Configuration menuStandard menu Extended standard menu Standard menu Direct ConfigurationApplicator Extended menu Display Function Values Standard menuInitialisation Init Dispensing speed Velo Start delay StadLabelling time Blow Display Function Data value Extended standard menu Sensor status Sens Label pitch LpitLabel contrast Label positionPOS Product length Prdl Egra value check Stst Electronic gear ratio adjustment EgraSlew speed Slew Dwell time APT1 Time constant compensation APT4 Restart delay APT3Blow on time APT2 Printer dwell time PDT End of air stream signal AstpSave parameter in data bank Save Load data bank Load Product menu Page Possible adjustments Configuration menuCalling the configuration menu Possible tests Display Function of the parameter Possible data entry Handling the menu Menu functions Type of applicator Appl Automatic product speed followerAPSF Additional functions in the standard menu Input and sensor check ICHOutput check OCH Interface baud rate Baud Adjustment resettingFACTParity bit Pari Number of stop bits Sbit Recycle simulates max labels/min Recy Number of data bits DbitDistance sensor to dispensing edge Dist Label counter Labc Leave Menu finishing Quit Serial interface Dispenser connector Signal description Pol DData of the serial interface Direction Code Description 25 pol Pol Sub Example Interface commandsCommand Description Range Ledg Message in display Output signals Connections and signals Applicator modes Signals for direct dispense Timing ASA applicator Control signals for the ASA applicator APT2 Signals for the EP applicator Applicator connector Applicator connector Connecting NPN left or PNP right inputs Input signals Product sensor Example for connecting an NPN sensor Datalogic NPN connection of optional ODC sensor OD Control sensor Connection of a NPN type Apsf sensor Apsf sensor Optional connector for process contro Control signals Internal I/O connector Rule EMI Electronic diagrams Wiring diagram Layout dispenser electronic board Resolution ALS 330/430 Page Dispenser error messages Errors and warningsSTO! Power-fail message Message Meaning How to solve Into Eeprom Dispenser warnings ALS 330/430 Description Details 330 430 Technical specificationTechnical Information APSF- Sensor Specification Optional function Application specification Charts Performance charts Performance chart Ramp Norm Deceleration Labels/min 900 25 mm 50 mm 75 mm 800 ALS 330/430 Page Function Factory Application Adjustment Function PD05 PD06 PD07 PD08 PD09 Function Factory PD01 PD02 PD03 PD04 Index