Connections and signals, Output signals | Avery ALS 330/430 specs

Operators Manual

ALS 330/430

8. Connections and signals

This machine has a number of inputs to connect sensor’s and a control. Outputs are available for applicators, a printer and other purposes.

8.1 Output signals

This machine has eight outputs, which switch the output from open circuit to + 24V. The maximum current must not exceed 500 mA. The four signals for error messages, machine ready, low material and warnings are available for other machines in the process or additional alarm signals. For connecting an applicator three signals are available and one additional for the printer.

The output signals are available at terminal connector CN33 on the main board. The wiring of the terminal is shown otherwise.

8.1.1Error and warning output

The outputs for errors and warnings are available on the terminal CN33 and optional on the I/O plug. The signals are switched active (+24V) if an error or warning occurs. When the error or warning is erased, the signal becomes passive again.

8.1.2Printer output

This machine can be connected to a printer. To use the printer the PDT parameter should be adjusted.

A new label cannot be dispensed until the printer dwell time set in PDT is over.

8.1.3OD-Control output

This output is switched active (+24V) if the OD-Control input is switched active during dispensing.

8.1.4Ready output

This output shows when the machine is ready for labelling. This output is switched inactive if there is:

•an error message appears in the display

•the mains supply voltage has fallen below specification

•the machine requires initialisation

•in OFF condition.

Release 4/06

Page 55

Connections and signals

Image 63

Avery ALS 330/430 manual Connections and signals, Output signals

Contents

Page Page ALS 330/430 Menu structure Errors and warnings ALS 330/430 Copyright Important NotesOverview Manufacturer General Safety Notes Safety Operator’s duty of care Concrete security regulations and symbols used Security measures during normal operation Security measures during maintenance and repairs Work on the electrical equipment Work on pneumatic equipmentObserve environmental regulations Mechanics Description Machine layout Operator panel Operator panel Plug board Plug board Electronics ALS 330/430 Installation Preparing the machinePrepare dispensing Define label data Manual adjustment of the Cont parameter Setting Lpit manually Capacitive sensor Capacitive label sensor Adjust dispense function Label guideStop position Product data bank Fixed dispensing speedAutomatic dispensing speed Apsf Label position on the product Operation Safety recommendation Left hand version Right hand version Inserting label material Mounting a new label roll Removing label material Mounting a new label roll on ALS Mounting a new label roll on ALS 330 Euro Rewind Adjusting the pressure roller Lead screw adjustment Adjustment of the dispensing edgePrinter adjustment Initializing new label material Adjust pressure roller Missing label function and web breaks Function Display message Mains switchControl of dispense unit Dispenser Menu selection Display and data input Dispenser active onDisplay Menu function Function data value Dispenser stopped OFF Material initialisation InitLabel position POS Start delaySTAD Stop position StodDispense speed Velo Maintenance Blow on time BlowProduct menu PD0n Release 4/06 Operation Page Extended standard menu Configuration menuMenu structure Standard menu Extended menu ConfigurationStandard menu Direct Applicator Standard menu Initialisation InitDisplay Function Values Start delay Stad Labelling time BlowDispensing speed Velo Display Function Data value Extended standard menu Label pitch Lpit Label contrastSensor status Sens Label positionPOS Product length Prdl Dwell time APT1 Electronic gear ratio adjustment EgraEgra value check Stst Slew speed Slew Restart delay APT3 Blow on time APT2Time constant compensation APT4 Load data bank Load End of air stream signal AstpPrinter dwell time PDT Save parameter in data bank Save Product menu Page Possible tests Configuration menuPossible adjustments Calling the configuration menu Display Function of the parameter Possible data entry Handling the menu Menu functions Type of applicator Appl Automatic product speed followerAPSF Input and sensor check ICH Output check OCHAdditional functions in the standard menu Number of stop bits Sbit Adjustment resettingFACTInterface baud rate Baud Parity bit Pari Label counter Labc Number of data bits DbitRecycle simulates max labels/min Recy Distance sensor to dispensing edge Dist Leave Menu finishing Quit Direction Code Description 25 pol Pol Sub Dispenser connector Signal description Pol DSerial interface Data of the serial interface Interface commands Command Description RangeExample Ledg Message in display Output signals Connections and signals Applicator modes Signals for direct dispense Timing ASA applicator Control signals for the ASA applicator APT2 Signals for the EP applicator Applicator connector Applicator connector Connecting NPN left or PNP right inputs Input signals Product sensor Example for connecting an NPN sensor Datalogic NPN connection of optional ODC sensor OD Control sensor Connection of a NPN type Apsf sensor Apsf sensor Optional connector for process contro Control signals Internal I/O connector Rule EMI Electronic diagrams Wiring diagram Layout dispenser electronic board Resolution ALS 330/430 Page Message Meaning How to solve Errors and warningsDispenser error messages STO! Power-fail message Into Eeprom Dispenser warnings ALS 330/430 Technical specification Technical InformationDescription Details 330 430 APSF- Sensor Specification Optional function Application specification Charts Performance charts Performance chart Ramp Norm Deceleration Labels/min 900 25 mm 50 mm 75 mm 800 ALS 330/430 Page Function Factory Application Adjustment Function PD05 PD06 PD07 PD08 PD09 Function Factory PD01 PD02 PD03 PD04 Index