Inserting label material | Avery ALS 330/430 instruction

Operators Manual

ALS 330/430

4.2 Inserting label material

Attention:

•Before threading the new material, the waste paper should be removed.

CAUTION! - Isertion/exchange of material should be carried out only by especially instructed personal.

Threading of the label material is shown down below on the threading diagrams for the right-hand and the left-hand version.

Left hand version		Right hand version

Figure 7 Threading diagram

Release 4/06

Page 24

Operation

Image 26

Avery ALS 330/430 manual Inserting label material, Left hand version Right hand version

Contents

Page Page ALS 330/430 Menu structure Errors and warnings ALS 330/430 Manufacturer Important NotesOverview Copyright Safety General Safety Notes Operator’s duty of care Concrete security regulations and symbols used Security measures during maintenance and repairs Security measures during normal operation Observe environmental regulations Work on the electrical equipmentWork on pneumatic equipment Description Mechanics Machine layout Operator panel Operator panel Plug board Plug board Electronics ALS 330/430 Prepare dispensing InstallationPreparing the machine Define label data Setting Lpit manually Manual adjustment of the Cont parameter Capacitive label sensor Capacitive sensor Stop position Adjust dispense functionLabel guide Label position on the product Fixed dispensing speedAutomatic dispensing speed Apsf Product data bank Safety recommendation Operation Inserting label material Left hand version Right hand version Removing label material Mounting a new label roll Mounting a new label roll on ALS 330 Euro Mounting a new label roll on ALS Adjusting the pressure roller Rewind Printer adjustment Lead screw adjustmentAdjustment of the dispensing edge Adjust pressure roller Initializing new label material Dispenser Menu selection Function Display message Mains switchControl of dispense unit Missing label function and web breaks Display Menu function Function data value Display and data inputDispenser active on Label position POS Dispenser stopped OFFMaterial initialisation Init Dispense speed Velo Start delaySTADStop position Stod Product menu PD0n MaintenanceBlow on time Blow Release 4/06 Operation Page Standard menu Configuration menuMenu structure Extended standard menu Applicator ConfigurationStandard menu Direct Extended menu Display Function Values Standard menuInitialisation Init Dispensing speed Velo Start delay StadLabelling time Blow Extended standard menu Display Function Data value Sensor status Sens Label pitch LpitLabel contrast Product length Prdl Label positionPOS Slew speed Slew Electronic gear ratio adjustment EgraEgra value check Stst Dwell time APT1 Time constant compensation APT4 Restart delay APT3Blow on time APT2 Save parameter in data bank Save End of air stream signal AstpPrinter dwell time PDT Load data bank Load Product menu Page Calling the configuration menu Configuration menuPossible adjustments Possible tests Handling the menu Display Function of the parameter Possible data entry Menu functions Automatic product speed followerAPSF Type of applicator Appl Additional functions in the standard menu Input and sensor check ICHOutput check OCH Parity bit Pari Adjustment resettingFACTInterface baud rate Baud Number of stop bits Sbit Distance sensor to dispensing edge Dist Number of data bits DbitRecycle simulates max labels/min Recy Label counter Labc Leave Menu finishing Quit Data of the serial interface Dispenser connector Signal description Pol DSerial interface Direction Code Description 25 pol Pol Sub Example Interface commandsCommand Description Range Ledg Message in display Connections and signals Output signals Signals for direct dispense Applicator modes Control signals for the ASA applicator Timing ASA applicator Signals for the EP applicator APT2 Applicator connector Applicator connector Input signals Connecting NPN left or PNP right inputs Example for connecting an NPN sensor Datalogic Product sensor OD Control sensor NPN connection of optional ODC sensor Apsf sensor Connection of a NPN type Apsf sensor Control signals Optional connector for process contro Internal I/O connector EMI Rule Electronic diagrams Wiring diagram Layout dispenser electronic board Resolution ALS 330/430 Page STO! Power-fail message Errors and warningsDispenser error messages Message Meaning How to solve Into Dispenser warnings Eeprom ALS 330/430 Description Details 330 430 Technical specificationTechnical Information Application specification APSF- Sensor Specification Optional function Performance charts Charts Performance chart Ramp Norm Deceleration Labels/min 900 25 mm 50 mm 75 mm 800 ALS 330/430 Page Adjustment Function Factory Application Function Factory PD01 PD02 PD03 PD04 Function PD05 PD06 PD07 PD08 PD09 Index