Barco MSWU-81E - page 26

MSWU-81E 07/08/2013

3.Physical Installation

This power cord for Europe

and Korea

This power cord for USA This power cord for China

Caution: Ensure that the power net meets the power requirements of t he projector.

WARNING: Do not attempt operation if the AC supply and cord are not within th e speciﬁed voltage and

power range.

CAUTION: Once the projector is switched to sta ndby, the lamp cooling fans will continue to run for approx-

imately ﬁve minutes to ensure that the projector and lamp have su fﬁciently cooled, at which point the

fans will automatically decrease to standby. To avoid thermal stress t hat can lead to premature lamp

failure, never unplug the power cord while the lamp cooli ng fans are running. Never unplug the power

cord to power down the projector, ﬁrst switch off the power switch and th en unplug the power cord.

Contents

Main Page Changes Copyright EN55022/CISPR22 Class A ITE (Information Technology Equipment) W Federal Communications Commission (FCC Statement) Guarantee and Compensation Trademarks Page 5. GETTING STARTED 29 6. ADVANCED OSD MENU 35 7. INPUT 37 8. IMAGE 40 9. LAYOUT 48 10. LAMP 51 11. ALIGNMENT 54 12. CONTROL 58 13. SERVICE 62 Page 1. SAF ETY About this chapter 1.1 General considerations W W W W W C 1.2 Important safety instructions To prevent the risk of electrical shock To prevent personal injury To prevent re hazard To prevent projector damage On servicing To prevent battery explosion 2. GENERAL About this chapter W 2.1 Installation requirements Environment conditions 2.2 Unpacking the projector 2.3 Initial inspection General Box content Mechanical check 2.4 Projector congurations Front projection Rear projection Positioning the projector On axis / off axis projection Shift range Horizontal and vertical projector tilt ranges B C 2.5 Projector air inlets and outlets Ventilation inlet: Ventilation outlet: Ventilation inlet Ventilation outlet 3. PHYSICAL INSTALL ATION About this projector 3.1 Remote control unit (RCU) Introduction Notes for the Remote control unit Remote Control overview 3.2 Lenses Available lenses for the MSWU-81E projector projector How to install the lens Click! Carefully align the connectors while installing the lens. How to remove the lens Lens focus Lens zoom Lens Shift Range of vertical lens shift adjustment 3.3 Connecting the projector with the power net Page 3.4 Alignment of a table mounted projector 3.5 Mounting the Ceiling mount Necessary tools How to mount N 4. PROJECTOR PARTS AND FUNCTIONS 4.1 Projector front view 4.2 Projector Rear view 4.3 Input and Communication 1 6 7 8 2 3 45 1. 10/100 BASE -T 2. RS232 3. 12V TRIGGER 4. IR EXT. 5. YUV1 6. HDMI 7. VG A 4.4 Status lights of LED 4.5 Connecting the projector to other devices HDMI connection 12V Trigger connection VGA connection Desk Top or Notebook RGBs connection Green Blue Red IR INPUT connection COMPONENT connection Y Pb Pr 5. GETTING STARTED 5.1 RCU & Local keypad How controlling the projector ? Location of the local keypad ? Remote control functions. Page 5.3 Power on projector How to power on. C Starting image projection via the standby key. 5.4 Switching to standby 25m 40 25m 40 5.7 Source selection Page 5.10 Introduction the OSD Lite on screen 6. Introduction the Advanced OSD menu 6. ADVANCED OSD MENU 6.1 How to activate the Advanced OSD menu 6. Introduction the Advanced OSD menu 6.2 How to navigate in the Advanced menu structure? How to make an OSD adjustment? 6.3 Advanced menu memory 7.Input 7. I NPU T 7.1 Input menu overview 7.Input 7.2 Input Selection 7.3 Input Conguration AUTO HDMI VGA Page 8. IMAGE 8.1 Image menu overview 8.2 Contrast 8.3 Brightness 8.4 Sharpness 8.5 Noise Reduction 8.6 Color Temperature 8.7 Input Balance Unbalanced color signals Black level B 0.7V Adjusting the input balance Offset Gain 8.8 Aspect Ratio 8.9 Timings H Total H Start Native picture Skewed left Skewed right 8.10 Auto Image 9.Layout 9. LAYOUT 9.1 Layout menu overview 9.2 Zo om 9.3 Main Select 9.4 PIP Select 9.5 PIP Position 9.5 PIP Pip/main source availability 10.Lamp 10. L AMP 10.1 Lamp menu overview 10.Lamp 10.2 Mode Mode Lamp2 10.3 La mps Lam p1 Page 11. ALIGNMENT 11.1 Alignment menu overview 11.2 Adjusting screen orientation Correct Picture Front projection - ceiling mode 11.4 Ceiling Mode 11.5 Lens Control Zoom Focus Shift 11.8 Gamma 11.8 Internal Patterns 11.9 Native EBU 12. CONTROL 12.1 Control menu overview 12.2 Eco Network Power 12.3 Network IP Address Subnet mask Gateway 12.4 Menu Position 12.5 Start Up Logo 12.6 Start Up Chime 12.7 Trigger1 ~2 12.8 Auto Source Off 13. SERVICE 13.1 Service menu overview 13.2 Service message of the projector 13.3 Lamp Hour Reset 13.4 Blue Only 13.4 Factory Reset 14. MAINTENANCE 14.1 Lamp Replacement W How to replace the projector lamp Page 14.2 Replace the lter (for inlet Ventilation) Page 14.3 Clean the dust lter(for outlet Ventilation) 14.4 Cleaning the lens Necessary tools How to clean the lens ? 14.5 Cleaning the exterior of the projector 14.6 Simple troubleshooting Problem Possible cause Solution 15.Projector Specications 15. PROJECTOR SPECIFICATION 15.1 Specications Description Specications 15.Projector Specications 15.2 STANDARD SOURCE FILES Page 74 16.Environmental information 16. ENVIRONMENTAL INFORMATION 16.1 Disposal information Disposal Information Disposal of batteries in the product Mercury Notice / 16.Environmental information 16.3 Production address Factorie s