Transport and Installation of the Machine | Baum Bros. Imports 26.4

1.0 Technical Data/Machine Layout/Transport and Installation of the Machine/Safety Relevant Machine Elements

Transport and Installation of the Machine

Have the machine installed by BAUM service personnel, exclusively!

The installation of the machine requires special skills which can be guaranteed only by especially trained experts of BAUM agencies. Arbitrary working on the machine may damage the machine itself or other material property of the user or cause accident endangering life and limb of the staff.

The machine must be unpacked, moved, transferred and installed by authorized BAUM Service Technicians only. Dangers might arise from the machine itself or from its packing if it is unpacked, moved, transferred or installed with unsuitable devices.

While the machine is unpacked, moved, transferred and installed, no other persons must be present in the range of the machine or its packing.

The BAUM Service Technician must also take care that no unauthorized persons work at the machine, its packing or the installation equipment.

After Unloading

•Remove all packing and wrapping material

•Check machine and accessories for damages

•Check for missing parts

In Case of Complaints

Immediately send written note to:

•Railway or shipping company

•Insurance company

•BAUM / Agency

Place of Installation

The location must meet the following requirements:

•Vibration free location

•Even concrete flooring, concrete property class min. (N/mm²) according to eurocode 2: C20/25 or according to DIN1045: B 25.

•Observe carrying capacity!

•Avoid possible accidents of operator by uneven flooring

•Adhere to minimum distance from buildings or peripheral equipment (see plan)

After the Installation of the Machine

1.Remove anti rust paint (agent: kerosene, gasoline) from the machine on the site of installation

Note:

Do not use any sharp tools to remove anti-rust paint!

2.Clean plastic covers only with plastic cleansing agent

3.Final check according to check list

4.Have handover signed

K1 - 4

Image 12

Baum Bros. Imports 26.4 manual Transport and Installation of the Machine, Place of Installation, Case of Complaints

Contents

Baumcut 26.4 Programmable Index K5AK5B Maintenance IndexK5C K5D Programmable Control Panel / Operating Elements Explanation of Pictographs on the Display Chapter Survey Chapter Survey Introduction Please pay special attention to the following informationCopyright Page Page Machine Layout Dimensions in mm Plan Transport and Installation of the Machine Place of InstallationAfter the Installation of the Machine Case of Complaints Power Supply Energy lead wire Type Plates Type plate Type plate Safety Relevant Machine Elements Safety Auxiliary ToolsWorking Area of Operating Personnel Placement of the warning label Durability Placement of the warning labels Label 1 Label 2 Label 3 Safety Signs Safety Signs / Warning Signs Technical Data Safety PrecautionsPermissible Environmental and Operating Conditions Hydraulic Data Voltage supply 3 phase 360 420V, 50/60Hz Voltage supply single phase AC 200 240, 50HzVoltage supply single phase AC 210 240, 60Hz Page Safety Symbol Page Electrical energy Start Up Switching Machine on Turning Machine OFFTo prevent a start-up of the machine Measurement Display and Measurement System Program Data DisplayPage Manual Operation Setting of Measurements Backgauge Movement by Hand Cutting Line Indicator, Mechanical with ClampCutting Line Indicator, Optical Actuate toggle switch 8 at main switch plate Clamp Pressure Adjustment Setting the Clamping TimeClamping and Cutting Light Barrier Interference into the light curtain causesTo continue the cutting process Continuation Light Barrier D2 D4 D1 D3Meaning of LEDs in display unit Clamping with False Clamp Plate Attaching false clamp plateRemoving of false clamp plate Automatic Operation Functions of the menu keys Key Main menu Function Survey Basic Displays Basic Display Program DataProgram Data Key Main Menu Function Survey Program Information Key Program Directory Contin. Basic Display Program Data Basic Display Program Information Press key Basic Display Program Directory 15755VAC Other input modes in this display Basic Display Main Menu Function Survey Press menu key Cursor Movement in Basic Display Automatic Backgauge Adjustment through Numerical Keyboard Measurement input in inchesProgram data display After 1. inputinput section shows Backgauge moves Input Error Value of Nom. Backgauge Position too Low/High Deletion of a Wrong InputMoving Backgauge to a Nominal Position Positioning Deletion of a wrong input Possible in all 4 basic monitor displays Make selection Program NumberDisplay example Selecting a Program According to order numberExample Continuing Selecting a Program Numerical keyboard Storage of Measurements Only in Program data display Setting Up a Cutting Program, Example Two side trim on size DIN A3 Untrimmed size 31 x 43 cmKey input Running the program Call program 5A Enter Correction of an Input Error Correcting before storingCorrecting after storing Automatic ON/OFF Automatic OFFPositioning check in automatic operation Made GO to Position Example Setting a cutting program, example Running a Cutting ProgramAfter cut Storing of Program Informations Press key Program InformationStoring Order End of information input Deletion of a Step Number Deletion of One/Several Programs PRO Deletion of Complete Memory Inserting of Measurements into a Program Storing of Measurements According to Printed Image Overflow Indicator Calculator FunctionsConditionsAutomatic OFF To set backgauge to a calculated size Using Backgauge Position of Calculations Switching the function offNegative Sign Machine Functions and Additional Functions Menu Keys Machine FunctionsAdditional Functions Machine Function Main Menu Function Survey Key Main Menu Key Main Menu includes the following functions Service Select Language / Measuring UnitSelect Main Menu Funtion survey Select function Language or Measuring Unit Knife Compensation Calibration to compensate for knifes of different thicknessSelect function Select Knife compensation Knife change Adjust time Resting Time for Knife at BDC Maintenance Cut Counter Set counter Preset Functions Selection of Main Menu Correction of Current PositionCalculate basic position Continuing Preset Functions Select function Preset functions Scan Reference PositionjPossible funtions in Auxiliary mode Abortion of reference run Adjustment of Display Contrast End of input with key Possibility of edge trim preadjusting Block Programming Setting up a Block Programming Example Variation 1, selection 1 Angular cut Selection of an input parameter with Block Programming Correction of an input parameter with Block ProgrammingDeletion of an input parameter with Block Programming Example Variation 1, selection Four trim cut Enter Edge trimFour trim cut Example Variation 3, selection 3 Four trim cut with labels Four trim cut with labels Block Programming Four-side trim with labels and trim cuts Right-hand lay side Enter outside trim Enter trimout measurement Block Programming Menu Key Additional Functions Storage of Additional Functions with Cut Size Subsequent Storing of Additional FunctionsErase Additional Function List of Additional Functions Additional function Jogging mark OperationEjector OFF K5C Menu Key Auxiliary Functions Cut and Record Sheet Size TablesAfter program generation Subtraction Repetition Unit Quitt the functionGraphics OFF K5D Menu Key Machine Parameters Adjustment of pre-pressure time Adjustment of BDC timePrepressure Time Make selection Knife Change Deposit knife in knife box!! Remove knife guard Knife Change Mounting the knife Adjustment of knife pre-tension Knife adjustmentAdjusting the knife Tighten up all knife bolts Changing of cutting stick Removing of cutting stickInserting of cutting stick Normal Turn overPage Malfunctions / Breakdowns Electrical Malfunctions/Breakdowns Remedy for machine malfunctions Start Up Breakdown Scan Reference Point/Auxiliary Mode Machine functions possible in Auxiliary Mode Breakdown Knife bar stops beneath the upper dead centre Breakdown Clamp stops beneath the upper dead centreKnife bar or clamp not in top dead centre Maintenance Basic information about servicing and maintenance work Quantity liters 22,5 Lubrication intervals weekly Cleaning of Display Hrs. per day equalPage Service Mr./Mrs Fax 937/492-7280Baum USA