90560838 ccs818 chain saw.qxd: chainsaw booklet new 2/12/10 10:07 AM Page 11

Remove sprocket cover (10) and allen head screws (11).

Cut the plastic wire tie holding the guide bar scabbard (12) to the guide bar (8). Be sure to cut away from yourself to prevent injury if cutting instrument should slip.

Wearing protective gloves, grasp the saw chain (9) and guide bar

(8)with one hand and pull the guide bar scabbard (12) off with your free hand.

Place the saw chain and guide bar assembly around the sprocket

(19).Check to make sure that the slot (20) in the guide bar (8) is over the two location pins (21) shown in figure E and that the hole below the slot is located over the adjustment pin (22).

Replace sprocket cover (10) and thread allen head screws (11) in with wrench until snug, then back wrench off one full turn.

Cut the plastic wire tie holding the saw chain to the guide bar. Be sure to cut away from yourself to prevent injury if cutting instrument should slip.

Pull bar nose up and keep it up as you adjust tension.

With the flat screwdriver end of the wrench provided rotate the tension adjustment screw (23) in the front of the housing clockwise to increase the chain tension as in figure F.

Follow instructions in “Adjusting Chain Tension” section.

While still holding the bar nose up, tighten the rear allen screw first, then tighten the front allen screw. Make sure both allen screws are securely tightened. Do not overtighten.

When the chain is new check the tension frequently (after disconnecting battery) during the first 2 hours of use as a new chain stretches slightly.

Replacing the Saw Chain

CAUTION: Sharp chain. Always wear protective gloves when handling the chain. The chain is sharp and can cut you when it is

not running.

WARNING: Sharp moving chain. To prevent accidental operation, insure that battery is disconnected from the tool before performing the following operations. Failure to do this could result in serious personal injury.

• Place the saw on a firm surface. Rotate the two allen head screws

(11)counterclockwise with the wrench (13) provided as shown in figure E.

To remove the saw chain (9), rotate the tension adjustment screw

(23)in the front of the housing using the flat screwdriver end of the wrench (13) as shown in figure F. Turning the screw counterclockwise allows the guide bar to recede and reduces the tension on the chain so that it may be removed.

Remove sprocket cover (10) and allen head screws (11).

Lift the worn saw chain (9) out of the groove in the guide bar (8).

Place new chain in groove of guide bar making sure saw teeth are facing correct direction by matching arrow on chain with graphic on housing shown in figure G.

Place the saw chain and guide bar assembly around the sprocket

(19).Check to make sure that the slot (20) in the guide bar (8) is over the two location pins (21) shown in figure E and that the hole below the slot is located over the adjustment pin (22).

Replace sprocket cover (10) and thread allen head screws (11) in with wrench until snug, then back wrench off one full turn.

Pull bar nose up and keep it up as you adjust tension.

Rotate the tension adjustment screw (23) in the front of the housing clockwise to increase the chain tension as in Figure F.

Follow instructions in “Adjusting Chain Tension” section.

While still holding the bar nose up, securely tighten the rear allen screw (11) first, then tighten the front allen screw.

When the chain is new check the tension frequently (after disconnecting battery) during the first 2 hours of use as a new chain stretches slightly.

Adjusting Chain Tension

CAUTION: Sharp chain. Always wear protective gloves when handling the chain. The chain is sharp and can cut you when it is not running.

WARNING: Sharp moving chain. To prevent accidental operation, insure that battery is disconnected from the tool before performing the following operations. Failure to do this could result in serious personal injury.

With the saw still on a firm surface check the chain tension. The tension is correct when the chain snaps back after being pulled

11

Page 11
Image 11
Black & Decker CCS818R instruction manual Replacing the Saw Chain, Adjusting Chain Tension

CCS818, CCS818R specifications

The Black & Decker CCS818 and CCS818R are innovative cordless electric saws designed for both professional and home use. These lightweight chainsaws are powered by an 18-volt lithium-ion battery, providing the freedom of movement without the constraints of a cord, making them perfect for a variety of cutting tasks in the garden or around the property.

One of the key features of the CCS818 and CCS818R is their 8-inch cutting bar, which allows for efficient cutting of limbs and small trees while ensuring portability and ease of use. Despite their compact size, these saws are capable of cutting through material with confidence, thanks to their robust chain system that grips and cuts smoothly through wood.

In terms of technology, the CCS818 models integrate an automatic oiling system to ensure the chain operates smoothly while reducing wear and tear. This feature simplifies maintenance, allowing users to focus on the task at hand rather than worrying about manual lubrication. Additionally, a transparent oil tank provides a quick view of oil levels, helping users monitor and maintain optimal performance.

The ergonomic design of the CCS818 and CCS818R further enhances their usability. The saws are equipped with a wraparound handle, providing a secure and comfortable grip, which reduces hand fatigue during extended use. The lightweight design also makes these saws user-friendly, especially for those who may not have prior experience handling a chainsaw.

Another characteristic worth mentioning is the tool-free chain tensioning system. This feature allows users to make chain adjustments quickly and easily without the need for additional tools, thus improving workflow efficiency. The CCS818 and CCS818R are also designed with safety in mind, equipped with a chain brake that helps prevent accidents and ensures safe operation.

In summary, the Black & Decker CCS818 and CCS818R chainsaws provide a perfect blend of power and convenience for anyone in need of a reliable cutting tool. Their lightweight design, lithium-ion battery power, automatic oiling, and ease of use make them standout choices for gardening enthusiasts and professionals alike. Whether trimming branches or tackling small tree removals, these chainsaws offer the performance and versatility needed to get the job done efficiently and safely.