Brother DH4-B980 instruction manual Using The Operation Panel And Front Panel

6. USING THE OPERATION PANEL AND FRONT PANEL

No.		Contents				Setting range	Initial
							value
07	Y direction offset for return seam to prevent					OFF: No offset	OFF
	thread breakage					ON: Offset by 1/2 pitch
08	Sewing end pitch		for buttonhole		taper to	OFF: No change	OFF
	prevent fraying					ON: Change
	No. of stitches before pitch change for memory
09	switch No. 08					01: 1 stitch, 02: 2 stitches, 03: 3 stitches,	01
	* Does not appear when memory switch No. 08					04: 4 stitches, 05: 5 stitches
	is set to OFF.
	No. of stitches after pitch change for memory					01: 1 stitch, 02: 2 stitches, 03: 3 stitches,
10	switch No. 08					04: 4 stitches, 05: 5 stitches, 06: 6 stitches,	01
	* Does not appear when memory switch No. 08
						07: 7 stitches, 08: 8 stitches, 09: 9 stitches
	is set to OFF.
11	Test feeding speed					OFF: Standard speed	OFF
						ON: Low speed
	Speed for memory switch No. 11					20: 20% of standard speed
12	* Does not appear when memory switch No. 11					35: 35% of standard speed	50
	is set to OFF.					50: 50% of standard speed
13	Knife operation (BEFORE/OFF/AFTER) setting					OFF: Setting not possible within cycle program	OFF
						ON: Setting possible within cycle program
14	Special lapel cutting device					OFF: Disabled	OFF
						ON: Enabled
15	Button hole sensor (Special lapel cutting					OFF: Disabled	OFF
	device)					ON: Enabled
	Timer for checking lowering of cutting block					OFF:Disabled (Determined from slit signal
16	(Timer for determining if cutting block is					stopping)	OFF
	lowered)					ON: Enabled (Determined by timer)
	Time for memory switch No. 16					42: 420 ms, 45: 450ms, 48: 480ms,
17	* Does not appear when memory switch No. 16						45
						51: 510ms, 54: 540 ms
	is set to OFF.
	Changing cutting block ON time					OFF: Disabled (25 ms)
18	* Disabled	(always	"OFF")	when	memory		OFF
						ON: Enabled
	switch No. 16 is "ON"
	Time for memory switch No. 18					05: 50 ms, 10: 100ms,
19	* Does not appear when memory switch No. 18						05
	is set to OFF.					15: 150ms, 20: 200 ms
	Timer for checking raising of cutting block					OFF: Disabled (Determined from number of slit
20	(Timer for determining if the cutting block has						OFF
	been raised to a position where it will not touch					signals)
						ON: Enabled (Determined by timer)
	the next feed bracket to operate)
	Time for memory switch No. 20					15: 150ms, 20: 200 ms, 25: 250ms,
21	* Does not appear when memory switch No. 20					30: 300ms, 35: 350ms, 40: 400ms,	20
	is set to OFF.					45: 450ms, 50: 500ms
	Cutting block raising check timer
	(Raised position of the cutting block is					OFF: Disabled
22	determined from the number of slit signals, and						OFF
	timer is updated)					ON: Enabled
	* Disabled	(always	"OFF")	when	memory
	switch No. 20 is "ON"
	Time for memory switch No. 22					05: 50 ms, 10: 100ms, 15: 150ms,
23	* Does not appear when memory switch No. 22					20: 200 ms, 25: 250ms, 30: 300ms,	05
	is set to OFF.					35: 350ms, 40: 400ms
24	Setting tacking length to 0 for straight tacking					OFF: Disabled	OFF
	specifications					ON: Enabled
25	Spare					-	-
99

28

RH-9800