Table 12 Ð Control Board LED Alarms
LED |
| ERROR | DESCRIPTION | TROUBLESHOOTING |
BLINKS |
| CODE | COMMENTS | |
|
| |||
1 |
|
| Normal Operation | The control board ¯ashes the red LED in |
|
|
|
| when the board is operating properly. Make sure DIP switch 3 is |
|
|
|
| closed. |
2 |
| Compressor 1 Safety | The high or low pressure safety switch for compressor no. 1 has | |
|
|
|
| opened for 3 seconds. The error will be cleared and compressor |
|
|
|
| no. 1 will be allowed to turn on in 15 minutes. If the safeties have |
|
|
|
| been tripped 3 times in 90 minutes, compressor no. 1 will be |
|
|
|
| locked out until the control board has been manually reset. |
3 |
| Compressor 2 Safety | The high or low pressure safety switch for compressor no. 2 has | |
|
|
|
| opened for 3 seconds. The error will be cleared and compressor |
|
|
|
| no. 2 will be allowed to turn on in 15 minutes. If the safeties have |
|
|
|
| been tripped 3 times in 90 minutes, compressor no. 2 will be |
|
|
|
| locked out until the control board has been manually reset. |
4 |
| Thermostat Failure | The thermostat is calling for both heating and cooling at the same | |
|
|
|
| time. The unit will operate on a ®rst call basis and will automati- |
|
|
|
| cally reset. |
5 |
| SAT Thermistor Failure | The | |
|
|
|
| wiring errors, then replace sensor. |
6 |
| OAT Thermistor Failure | The | |
|
|
|
| for wiring errors, then replace sensor. |
7 |
| DIP Switch 2 is Open | Close DIP switch 2. | |
8 |
| DIP Switch 1 is Open | Close DIP switch 1. | |
9 |
| Loss of Communications | Communications between the expansion board and the control | |
|
|
| with Expansion Board | board have been interrupted. Ensure that an expansion board |
|
|
|
| is installed and wired using the wire harness supplied with the |
|
|
|
| expansion module. If an expansion board is not used, ensure that |
|
|
|
| DIP switch position 3 is in the closed position and reset power. |
10 |
| Control Board Failure | Generated when hardware has failed on control board. Replace | |
|
|
|
| the control board. |
11 |
| Expansion Board Failure | Generated when hardware has failed on the expansion board. | |
|
|
|
| Replace the expansion board. |
LEGEND |
|
|
| |
DIP Ð Dual |
|
| ||
LED Ð |
|
|
II. ERROR CODE SUMMARY
A summary of the error codes is listed in Table 13. If more than one error code exists, they will be displayed on the LED of the IGC board in sequence. Fault history is deleted when power is turned off.
Table 13 Ð IGC Board Error Code Summary
INDICATION | ERROR MODE | |
ON | NORMAL OPERATION | |
OFF | HARDWARE FAILURE | |
1 | FLASH | FAN ON/OFF DELAY MODIFIED |
2 | FLASHES | LIMIT SWITCH FAULT |
3 | FLASHES | FLAME SENSE FAULT |
4 | FLASHES | 4 CONSECUTIVE LIMIT SWITCH FAULTS |
5 | FLASHES | IGNITION LOCKOUT FAULT |
6 | FLASHES | INDUCED DRAFT MOTOR FAULT |
7 | FLASHES | ROLLOUT SWITCH FAULT |
8 | FLASHES | INTERNAL CONTROL FAULT |
|
|
|
III. INPUT AND OUTPUT CHANNEL DESIGNATIONS
Table 14 shows the input and output channel designations.
The Integrated Gas Controls for heating and cooling are shown in Fig. 45.
Ð34Ð