Honeywell Complete Guide to Programming the Vista 50P Home Security System

*80	*81	SYSTEM NON-ALARM CODES
		Enter 00-09; B-F (11-15).
		Default = 00 for all reports
		*80 1st Digit	*81 2nd Digit

1*20 EXIT ERROR LOGIC ENABLE	[0]
0=No; 1=Bypass E/E and Interior zones faulted after exit
delay.
Must be "0" for UL installations.

Close

Open

Low Battery

Low Battery Restore

AC Loss

AC Restore

Test

Power Up

Cancel

Program Tamper

*83 FIRST TEST REPORT TIME

1*21 EXIT DELAY RESET [0]

0=No; 1=Resets Exit Delay to programmed value after zone is closed and then faulted prior to end of exit delay.

Must be "0" for UL installations.

FIELDS 1✳22-1✳25: Allow four sets of two zones each to be linked so that both must fault within a five minute period to cause an alarm. Default for these fields = [000], [000].

1*22	CROSS-ZONING PAIR ONE
1*23	CROSS-ZONING PAIR TWO
1*24	CROSS-ZONING PAIR THREE
1*25	CROSS-ZONING PAIR FOUR

MISCELLANEOUS WIRELESS OPTIONS

Fields 1*28 - 1*31 are not applicable for UL installations.

1*28 RF TX LOW BATTERY SOUND	[0]
1=immediate; 0=when disarmed

[Day 00; hour 12; min 00] Days 01-07 Hours 00-23 Min 00- 59; 00 in all boxes = instant (Day 01= Monday)

*84 SWINGER SUPPRESSION [01]

01-15 alarms

Must be "00" (disabled) for UL.

*85 ENABLE DIALER REPORTS FOR PANICS & DURESS

1=enable; [0=disable]

995 996 999 Duress

*87	ENTRY WARNING				[1]
	1=continuous; 0=3 beeps
*88	BURG. ALARM COMM. DELAY				[0]
	1=16 seconds; 0=no delay
	Must be "0" for UL installations.
*89	RESTORE REPORT TIMING				[0]
	0=Instant; 1=After bell timeout if zone is restored; 2=when
	system is disarmed. Must be "0" for UL installations.
*90	SEC. SUBS. ACCT #
	Enter 00-09; B-F (11-15)			[15 15 15 15]
2nd Page Programming Fields (press *94)
1*01			1*09 ASSIGN RESPONSE TYPE FOR ZONES.
			Skip these fields. Use #93 Menu Mode, Zone
			Programming to program the response types.
1*17		LOBBY PARTITION			[0]
		Enter the "common lobby" partition (1-8)
1*18		AFFECTS LOBBY			[0]
		Enter 1 if this partition affects the common lobby;			enter 0 if it
		does not.
		Must be "0" for UL installations.
1*19		ARMS LOBBY			[0]
		Enter 1 if arming this partition attempts to arm lobby; enter 0
		if it does not.
		Must be "0" for UL installations.

1*29	RF TX LOW BATTERY REPORTING		[0]
	1=enable; 0=disable
1*30	RF RCVR CHECK-IN INTERVAL	[06]
	02-15 times 2 hours; 00 disables supervision
1*31	RF XMITTER CHECK-IN INTERVAL	[12]
	02-15 times 2 hours; 00 disables transmitter supervision
1*33	TOUCHTONE W/ROTARY BACKUP		[0]
	1=enable; 0=disable
1*34	COMM. SPLIT REPORTING		[0]

0=no; 1=alarms and alarm restores primary, others secondary; 2=open/close, test secondary, others primary. See 751 for comments if using with dual reporting.

1*35 1*38 ALARM REPORT CODES & ID DIGITS FOR ZONES 65-80.

Skip these fields. Use #93 Menu Mode, Zone

Programming to program the report codes.

1*39 SUPERVISORY AND RESTORE CODES FOR ZONES 65-80.Enter 00-09; B-F (11-15).

Default = [00 00 00 00 00]

Alarm Rst Trbl Trbl Rst Byp Byp Rst

– 7 –