Honeywell Vista-50P/Vista-50PUL manual Partition-Specific Fields, 1st Page Fields

Partition-Specific Fields

(Duplicate this page for each partition in the installation.)

To program these fields,

1.Press *91 to select a partition.

2.Enter a partition-specific field number (ex. *09).

3.Make the required entry.

4.Repeat steps 1-3 for each partition in the system.

PARTITION #____ PROGRAM FIELDS

1st Page Fields	*87	ENTRY WARNING	[1]
*09 ENTRY DELAY #1	[02]	1=continuous; 0=3 beeps

00, 02-15 times 15 seconds.

Maximum 03 for UL Listed installations.

*10	EXIT DELAY #1	[03]
	00, 03-15 times 15 seconds.
	Maximum 04 for UL Listed installations.
*11	ENTRY DELAY #2	[06]
	00, 02-15 times 15 seconds.
	Maximum 03 for UL installations.

*88	BURG. ALARM COMM. DELAY		[0]
	1=16 seconds; 0=no delay.
	Must be "0" for UL installations. Must be “1” for SIA
	installations.
*90	SEC. SUBS. ACCT #
	Enter 00-09; B-F (11-15)	[15 15 15 15]

2nd Page Programming Fields (press *94)

*12 EXIT DELAY #2 [08]

00, 03-15 times 15 seconds. Maximum 04 for UL installations.

1*18 AFFECTS LOBBY [0]

Enter 1 if this partition affects the common lobby; enter 0 if it does not.

*13 ALARM SOUNDER DURATION [04]

01-15 times 2 minutes.

Must be minimum 16 minutes for UL installations.

1*19 ARMS LOBBY [0]

Enter 1 if arming this partition attempts to arm lobby; enter 0 if it does not

*16	CONFIRMATION OF ARMING DING
	1=enable; 0=disable.
	Must be "1" for UL installations.
*22	KEYPAD PANIC ENABLES	[001]
	1=enable; 0=disable	995
*23	MULTIPLE ALARMS
	1=yes; 0=no.
	Must be 1 for UL installations.
*29	QUICK ARM
	1=yes; 0=no

[0]		1*20	EXIT ERROR LOGIC ENABLE	[0]
			0=No; 1=Bypass E/E and Interior zones faulted after exit
			delay.
		1*21	Must be "0" for UL installations.
			EXIT DELAY RESET	[0]
996	999		0=No; 1=Resets Exit Delay to programmed value after zone
[1]			is closed and then faulted prior to end of exit delay.
			Must be "0" for UL installations.
	1*43
			PERM. KEYPAD BACKLIGHT	[0]
[1]			1=enable; 0=disable. When disabled, display lights when
			any key is pressed, and turns off after period of keypad
			inactivity.

*32	PRIM. SUBS. ACCT #
	Enter 00-09; B-F (11-15)	[15 15 15	15]
*38	PREVENT ZONE XX BYPASS			[00]
	01-86; 000 if all zones (except fire zones)			can be bypassed
*39	ENABLE OPEN/CLOSE REPORT				[0]
	FOR INSTALLER CODE
	1=enable; 0=disable
*84	SWINGER SUPPRESSION			[01]

01-15 alarms;

Must be "00" (disabled) for UL installations..

*85 ENABLE DIALER REPORTS FOR PANICS & DURESS

1=enable; [0=disable]

995 996 999 Duress

1*45	EXIT DELAY SOUNDING	[0]
	1=enable; 0=disable. Produces quick beeping during exit
	delay if enabled.
1*47	CHIME ON EXTERNAL SIREN	[0]
	1=enable; 0=disable
1*52	SEND CANCEL IF ALARM + OFF	[1]
	1=no restriction; 0=within Bell Timeout period only
1*76	ACCESS CONTROL RELAY FOR PART.[00]
	Relay will be pulsed for 2 seconds whenever code + [0] is
	pressed. Enter 00-16; 00=none.
	Must be "00" for UL installations.

– 10 –