Ademco VISTA-50P/VISTA-50PUL Summary of Connections

— 47 —

WARNING: OWNER'S INSTRUCTION NOTICE NOT TO BE REMOVED

WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM.

NOTES:

1. Zone 1 may be selected for EOLR supervised

4. Zone 8 supports 2-wire latching type glass break detectors.

J7 Header

J8 Header

MAKE CONNECTIONS USING

or normally closed (no EOLR) operation via

See Installation and Setup Guide for recommended type

1. Not Used

1. In 2 (Printer DTR)

Optional programming:

No. 4142TR CABLE

cut jumper. (Cut red jumper for normally closed

and maximum number of detectors supported.

2. Ground-

Ground

Out 1: Open/close or keypad-like sounding

Blue

operation. Do not cut for Fire Usage). Zones 2-8

5. Cut blue jumper to disable supervision of alarm sounder output.

3. Out 1 (Ground Start)

3. In 3 (1361X10 sync)

Out 2: Armed LED

may be selected for either operation via program

4. Ground-

4. In 4 (1361X10 sync)

Out 4: Ready LED

Jumper

field *41.

Leave jumper intact to supervise output. (See Installation and

(note 5)

5. Out

2 (fire)

Ground

Ratings for Out 1:

2. Zone 1 supports 2-wire smoke detectors.

Setup Guide for Programming and Wiring Instructions).

6. Ground-

6. Out 5 (1361X10 data) Active: 10VDC-13.8VDC through 4k OHMS

1 2 3 4 5 6 7 8 9

See Installation and Setup Guide for recommended

7. Out

3 (burg/aud. panic) 7.

Out 6 (Printer RXD)

Not Active: 100 OHMS to ground

BATTERY

type and maximum number of detectors supported.

8. Ground

Ground

Ratings for out 2-4:

Connect to

9. Out 4 (silent panic/

Ground

Active: 10VDC-13.8VDC through 5k OHMS

TABS

3. Zone 7 may be used for remote keyswitch

Not Active: 1k OHMS to ground

12VDC,

duress)

(+)

4AH - 17.2AH

arming/disarming. See Installation and Setup Guide

Red Jumper

(Refer to Installation Instructions for information concerning Direct Wire

1 2 3 4 5 6 7 8 9

RED

for wiring instructions.

Downloading and printer connections using the 4100SM Serial Module.)

SEALED LED

(note 1)

ACID BATTERY

ZONE 2 ZONE 3

ZONE 4 ZONE 5

ZONE 6 ZONE 7

ZONE 8 ZONE 9

EARTH GROUND

CHARGING

Connect to good earth

VOLTAGE

(–)

ground to maintain im-

13.7VDC

–

munity to transients.

See

BLK

ZONE 1

(BROWN)

(GRAY)

(GREEN)

(RED)

See Instructions for

Instructions for

out

–

DOC LOAD NO.: 5

required

RING

TIP

RING

Installation

CONNECTION

SMOKEWIRE-2 DETECTORLOOP NO/NCsupportsBurgcontacts)

LATCHINGTYPE GLASS

DETECTORBREAK LOOP

ProgrammableResponse (Fast/Normal)Loop

POLLINGLOOP

TIP

proper grounding.

ADEMCO No.1361

for max. # of keypads

2k EOLR

THIS EQUIPMENT SHOULD BE INSTALLED

capacity

Connect to

–

Data

Handset

Incoming

Replace

24hr. 120VAC,

N.C.

Phone Line

WARNING: TO PREVENT

every

60 Hz Outlet

Red

Blk

Grn

Yel

RISK OF ELECTRICAL

3 years

Telephone connections

SHOCK, DISCONNECT

REMOTE KEYPAD/DEVICES

using Ademco No. 620

(Addressable keypads) only

N.O.

RJ31X direct connect

TELCO JACK BEFORE

cord.

SERVICING THIS PANEL.

TRANSFORMER

16.5VAC, 40VA

See Installation Instructions

(IN CANADA USE

BELL

and for max. wire run length.

(Also

(note 1)

(note 1,3)

–

4208U

IN ACCORDANCE WITH THE NATIONAL

No. 1361CN)

–

OR 1361X10

–

Fire

GLASS

FIRE PROTECTION ASSOCIATION'S

IF X-10 DEVICES

–

AUXILARY POWER OUTPUT

STANDARD 72, CHAPTER 2 (NATIONAL FIRE

WILL BE USED

Usage

BREAK

9.6VDC - 13.8VDC,

N.C.

PROTECTION ASSOC., BATTERYMARCH

NOTE:

750mA maximum

SMOKE

N.C.

4192SD

PARK. QUINCY, MA. 02269). PRINTED

Note: Include current drawn

N.C.

SMOKE

WHEN POWERING UP THE PANEL,

by keypads and polling loop

INFORMATION DESCRIBING PROPER

PLUG THE TRANSFORMER IN BEFORE

SIREN

devices when making

N.O.

INSTALLATION, OPERATION, TESTING,

CONNECTING THE BATTERY.

auxiliary power calculations.

N.C.

4190

N.O.

N.C.

MAINTENANCE, EVACUATION PLANNING

ALARM SOUNDER OUTPUT

Burg.

AND REPAIR SERVICE IS TO BE

10VDC - 13.8VDC, 1.7A max

Usage

2k EOLR

PROVIDED WITH THIS EQUIPMENT.

For Household Fire Installations,

N.O.

(note 1)

(note 1,4)

USE UL LISTED ENERGY CABLE FOR ALL CONNECTIONS

supervise alarm sounder output (Note 5)

Zone resistance (Excluding EOLR):

and limit combined alarm sounder,

2k EOLR

ZONE 1,8: 100 OHMS MAXIMUM

Polling loop rating: 64mA max. See

aux power and polling loop current to 750mA.

ALL OTHER ZONES: 300 OHMS MAXIMUM

Installation Instructions for maximum

COMPLIES WITH FCC RULES, PART 68

(note 1,2)

Zone response time:

number of devices supported and

FCC REGISTRATION NO. AC398U-68192-AL-E

ZONES 1-8: 350mSec-500mSec

maximum wire run length.

RINGER EQUIVALENCE: 0.7B

ZONE 9: Programmable for

CONNECTION OF THE FIRE ALARM SIGNAL

THIS DEVICE COMPLIES WITH PART 15 OF

Fast: 10mSec-15mSec

TO A FIRE ALARM HEADQUARTERS OR A

FCC RULES. OPERATION IS SUBJECT TO THE

Normal: 350mSec-500mSec

CENTRAL STATION SHALL BE PERMITED

ALL CIRCUITS ARE

(default response)

ONLY WITH THE APPROVAL OF THE LOCAL

FOLLOWING TWO CONDITIONS: (1) THIS DEVICE

AUTHORITY HAVING JURISDICTION. THE

MAY NOT CAUSE HARMFUL INTERFERENCE, AND

POWER LIMITED

BURGLAR ALARM SIGNAL SHALL NOT BE

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE

CONNECTED TO A POLICE EMERGENCY

RECEIVED, INCLUDING INTERFERENCE

NUMBER.

THAT MAY CAUSE UNDESIRED OPERATION.