Honeywell Vista-50P/Vista-50PUL manual Relay Devices Programming, Enter Relay #

Relay Devices Programming

From Data Field Programming Mode, press #93 to display the "ZONE PROG?" prompt. Press [0] (NO) to each menu option until the "RELAY PGM?" prompt appears. Press [1] (YES).

While in this mode, press [✱] to advance to next screen. Press [#] to back up to the previous screen.

PROMPTEXPLANATION

ENTER RELAY #

(00=QUIT) 01

02A EV ZL ZT P STT 0 0 00 00 0

02A ZL ZT P STOP 0 00 00 0

02	RELAY ACTION
NO RESPONSE		0
02	START EVENT
NOT USED		0

Enter the relay (output device) identification number 01-16. This is a reference number only, used for identification purposes. The actual module address and relay number on the module are programmed in the last two prompts.

Press [✱] to continue.

Press [✱] to continue.

The keypad displays a summary STOP screen.

Press [✱] to continue.

The Relay Action is the way in which the relay will respond when activated by the "start" event. Enter the desired action for this relay as follows:

0=not used; 1=close for 2 secs.; 2=stay closed; 3=pulse on/off

An output may be activated by an Event/Zone List combination, and/or by a Zone Type/System Operation. For an Event/Zone List combination, enter the event code as follows:

0=not used; 1=alarm; 2=fault; 3=trouble

If you are not using a Zone List to activate the relay, enter 0. Press [✱] to continue.

02	START: ZN LIST
		0
02	START: ZN TYPE
NO RESPONSE		00

A zone list is a set of zones that can be used to initiate the start or stop relay action. If a zone list is being used to start this relay action, enter the zone list number, 1-8. If a zone list is not being used, enter 0.

Press [✱] to continue.

A Zone Type/System Operation can be used instead of or in addition to an Event/Zone List combination or a specific zone to start the relay action. If a Zone Type/System Operation is being used, enter the 2-digit code as listed in the table that follows.

Press [✱] to continue.

Choices for Start/Stop Zone Types and System Operations:

00	= No Response (Not Used)		23	= No Alarm Response
01	= Entry/Exit #1	31		= End of Exit Time
02	= Entry/exit #2	32		= Start of Entry Time
03	= Perimeter	33		= Any Burglary Alarm
04	= Interior Follower	34		= Code + [#] + 71 Key Entry
05	= Trouble Day/Alarm Night			= Code + [#] + 72 Key Entry
		35
06	= 24-Hr. Silent	36		= At Bell Timeout **
07	= 24-Hr. Audible	37		= 2 Times Bell Timeout **
08	= 24-Hr. Auxiliary	38		= Chime
09	= Fire Alarm or Trouble	39		= Fire Alarm
10	= Interior W/Delay	40		= Bypassing
20	= Arming-STAY***	41		= AC Power Fail
21	= Arming-AWAY****	42		= System Battery Low
22	= Disarming (Code + Off)

*Stop condition only

**Or at disarming, whichever occurs earlier

***The output also activates when the partition is armed in the INSTANT mode

****The output also activates when the partition is armed in the MAXIMUM mode

43 = Communication failure

44 = RF Low Battery

45 = Polling Loop Failure

51 = RF Receiver Failure

52 = Kissoff

54 = Fire Zone Reset

55 = Disarm + 1 Minute

56 = XX Minutes (enter XX in field 1*74) * 57 = YY Seconds (enter YY in field 1*75) * 58 = Duress

60 = Audio Alarm Verification (must be selected for both START and STOP operation)

If you are using options 56 and/or 57 (usually as the STOP Zone Type), you must program data fields 1*74 and 1*75 for the respective relay timeouts for minutes and seconds.

– 26 –