Manuals / Bush Hog / Lawn and Garden / Compact Loader

Bush Hog 3860 QT manual Ref. Qty. Description 1 2 Grapple Cylinder 2-1/2, 11 2 Flatwasher 3/8

Models: 3860 QT

1 46

Download 46 pages 54.16 Kb

Page 41

Ref. Qty. Description

Figure 10

Ref. Qty. Description

12 Grapple Cylinder 2-1/2"

24 Fitting, 90° NPTF 1/2" x ORBM 3/4"

34 Clevis pin 5/16" x 2" Heat Treated for use on 1-1/8" pins

2 Clevis pin 3/8" x 2-1/4"

for use on 1-5/16" pins.

46 Cotter Pin 1/8" x 1"

51 Hose 3/8" x 47.72" Top Left

61 Hose 3/8" x 27.48" Top Right

71 Hose 3/8" x 42.73" Bottom Left

81 Hose 3/8" x 22.98" Bottom Right

91 Quick Coupler Mount

101 Hex Bolt 3/8"-16NC x 3-1/2" Grade 5

112 Flatwasher 3/8"

Ref.	Qty.	Description
12	2	Hex Nut 3/8" Nylon Lock
13	1	Hex Bolt 3/8"-16NC x 1-3/4"
		Pin On Bucket only, or
	1	Weld-on Stud

Quick Draw Bucket only.

141 Hose Clamp Plastic 5/8 x 5/8

151 Hose Bar Support 3/16" x 1" x 2-1/2"

161 Quick Coupler Male ORBF 3/4"

171 Quick Coupler Female ORBF 3/4"

181 Quick Coupler Dust Plug

192 Bulkhead O-Ring 3/4"

202 Fitting Str. Bulkhead JIC M 3/4"-16

212 Bulkhead Nut 3/4"-16

222 Fitting Tee JIC M-M-F 3/4"-16

39

Image 41

Bush Hog 3860 QT manual Ref. Qty. Description 1 2 Grapple Cylinder 2-1/2, 2 4 Fitting, 90 NPTF 1/2 x ORBM 3/4, Weld-on Stud

Contents

OPERATION MAINTENANCE Front End LoaderBUSH HOG Model 3860 QTCONGRATULATIONS RETAIL CUSTOMER’S RESPONSIBILITY UNDER THE BUSH HOG WARRANTY TABLE OF CONTENTS3860 QT PAGETHIS LIMITED WARRANTY SHALL NOT APPLY LIMITED WARRANTYOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOODEALER PREPARATION CHECK LIST 3860 QT LOADERTHE LOADER IMPORTANT SAFETY PRECAUTIONSTHE TRACTOR OPERATING THE LOADER SAFETY PRECAUTIONS CONTINUEDIMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONSDESCRIPTION 1. INTRODUCTION AND DESCRIPTIONINTRODUCTION Digging Depth Model 3860 QT Technical Specifications2. INSTALLATION INSTRUCTIONS Page TORQUE IDENTIFICATION LIFT AND SUPPORT ALL LOADER COMPO- NENTS SAFELYLoader Subframe Loader Subframe to Front Crossbrace Asembly 3 each sideTRANSMISSION FLUID 3. PRE-OPERATION INSTRUCTIONSINITIAL LOADER OPERATION EXTERNAL LOADER AND/OR TRACTOR VALVEBucket Level Indicator BUCKET LEVEL INDICATORNEUTRAL POSITION FLOAT POSITIONTHIRD CYLINDER TUBE KIT OPTIONAL REMOTE HOSES SUPPORT4. MAINTENANCE GENERAL SAFETY 5. OPERATING INSTRUCTIONSBUCKET LEVEL GAUGE ROD OPERATIONFILLING THE BUCKET Approach and enter the pile with a level bucket CARRYING THE LOAD FLOAT OPERATING WITH FLOAT CONTROLSidecutting is a good technique for cutting down a big pile FLOAT SURFACE MATERIAL LOADING FROM A BANKBACKFILLING PEELING AND SCRAPING 6”IMPORTANT To prevent damage to cylinders 1 Do not backgrade with bucket cylinders extendedHANDLING LARGE HEAVY OBJECTS PROBLEM TROUBLESHOOTING PROCEDURESsetting recommended POSSIBLE CAUSE6. DISMOUNTING THE LOADER NOTE Driving the tractor forward slowly while positioning loader will allow parking stands to contact ground firmly. Using float position dur- ing this operation will keep tractor weight from being applied to loader parking stands 7. MOUNTING THE LOADER 1 Clevis pin 5/8 x 4-1/2, one each side of loader 1 Subframe being lowered to center mounting bracket2 Clevis pin 5/8 x 4, one each side of loader 3 Lower parking stand leg extended8. INSTALLATION & OPERATION OF QUICK DRAW LATCH ATTACH 1 Handle disengaged position 1 Upper channel 2 Weld-in center support 3 Bucket or attachment2 Handle engaged position 3 Quick draw notch 4 Handle engaged arrow of decal9. INSTALLING BUCKET OR ATTACHMENT TO QUICK DRAW LATCH ATTACH 1 Quick draw pin 2 Quick draw pin bushing 10. REMOVING BUCKET OR ATTACHMENT FROM QUICK DRAW LATCH ATTACH 11. BUCKET ATTACHMENT 12. SUPER PENETRATOR BALE PROBE ATTACHMENT 14. MANURE FORK ATTACHMENT 13. DOZER ATTACHMENTPARKING ANGLES 15. PALLET FORK ATTACHMENT16. GRAPPLE ATTACHMENT Page 1 Bucket 3 Quick coupler mount 4 Center punch and drill 7/16 hole 2 Clevis pin 3/8 x 2-1/4 for use on 1-5/16 pins 4 6 Cotter Pin 1/8 3 4 Clevis pin 5/16 x 2 Heat Treated for use on 1-1/8 pinsRef. Qty. Description 1 2 Grapple Cylinder 2-1/2 2 4 Fitting, 90 NPTF 1/2 x ORBM 3/4SUPPLEMENTAL INSTRUCTIONS FOR FORD GENESIS SPECIAL WIRES SAFETY DECALSDANGER LIVEDECALS CONTINUED AMERICAN TORQUE SPECIFICATIONSMETRIC Bolt Head Markings