Cabletron Systems 9A100 manual

Switch Installation and Setup								Configuring the Switch

Terminal

RJ-45

Port

Terminal

Ethernet

RJ-45

Port

Ethernet

Hub

Figure 2-3 SmartSwitch 9A100 console and network connections

–•Start the dumb terminal or PC and its terminal emulation software.

••When power is applied to the SmartSwitch 9A100, the module emits a series of diagnostic messages. If you inserted the module into a chassis that was turned off, turn it on now; the diagnostics will appear after a 6-second delay. If you inserted the module into a chassis that was turned on, press the Reset switch to see the diagnostics.

G• After the diagnostics are finished, the switch prompts for a password. Enter the default password, "admin."

SmartSwitch 9A100 User Guide 2-7

Image 25

Cabletron Systems manual SmartSwitch 9A100 console and network connections

Contents

SmartSwitch 9A100 User Guide SmartSwitch 9A100 User Guide FCC Class a Notice Declaration of Conformity Addendum Safety Information Class 1 Laser Transceivers Fiber Optic Protective Caps Regulatory Compliance Summary Safety Revision History Table of Contents Specifications Acronyms Index Xii SmartSwitch 9A100 User Guide List of Figures List of Figures Xiv SmartSwitch 9A100 User Guide List of Tables List of Tables Xvi SmartSwitch 9A100 User Guide Introduction Introduction SmartSwitch 9A100 User Guide Unpacking the Switch Switch Installation and SetupCheck Accessory Carton Contents SmartSwitch 9A100-04 front panel Inspecting the Switch 1 DS3 and E3 I/O Module Configuration Installing the Switch Installing the SmartSwitch 9A100 Configuring the Switch SmartSwitch 9A100 console and network connections Console Commands Using the Console SmartSwitch # show portconfig a1 Console Time-out SmartSwitch # set consoletimeoutCreating an Alias Traffic SwitchTrafficCongestion. For example Ambiguous Commands SmartSwitch # ? add laneclient Smartswitch ATM AdministratorConsole Help Exterior SmartSwitch ATM Administrator MB RAM Installation Steps Accessing Online Help Starting SmartSwitch ATM Administrator the First TimeUser Name Access Level Default Password SmartSwitch ATM Administrator IP Over ATM and Lane SmartSwitch # add ipatmclientCreating AN IP Over ATM Vlan Server Is local Server Connection Established ATM Addressing for IP over ATM Creating AN Emulated LAN3900000000000000000014418000005A01010100 No Lane server address is specified see note below Add Elan Ilmi ATM Addressing for LAN Emulation ELANs Across Multiple Switches SmartSwitch# add laneclient Switch ClientsElan1 Page Backing UP and Restoring Switch Configuration Switch AdministrationPath /backdir/config-1 SmartSwitch # show netprefix b2 SmartSwitch# restore switchATM Routing Creating an Iisp Route Atmroute AtmAddress Iisp route across Pnni domain UNI Routes Route Metrics IP Routing SmartSwitch # show pnnimetrics Route NET Table 90.1.1.254 Event Categories Events and Alarms SmartSwitch # set eventdisplay Viewing Events and Alarms SmartSwitch # set alarmdisplay Deleting Events and AlarmsPVC Connections SmartSwitch # show trafficdescriptor SmartSwitch # add trafficdescriptorPoint-to-Point PVCs 100 Md1 #add trafficdescriptor Point-to-Multipoint PVCs Local Connecting to Local Switch Client Through a PVC10.1.1.0 VCC Mask Index VPI Bits VPI Values VCI Bits VCI Values Non-zero VPIs SmartSwitch # set portconfig a1 Use show portconfig to see the change to port A1 Traffic Descriptors Traffic Management Traffic Descriptor with CLP and best effort Type Number Descriptor Characteristics 8000 Call Admission Control Policy5000 Ubr Min for CBR queue SmartSwitch # set porttrafficcongestion SmartSwitch # show switchtrafficcongestion QoS Queue Recommended SettingsEFCI, EPD, and RM Thresholds Upgrading and Changing Software Accessing the Boot Load Prompt Command Action Parameters Boot Load Commands Boot Prom Upgrading Boot Load SoftwareFlash RAM =df b =chpi Upgrading Post Diagnostic Software=df p =df s Upgrading Switch Operating Software SmartSwitch # update firmware Using the Update Firmware Command214.95.77.240 Saving Core Dumps Set CoreDump command Tftpboot/bobr/core204.95.77.240 Bobr Error IP e0103288 PFP e04be080 R0pfp e04be040 R1sp e04be0c0 Troubleshooting IP Over ATM Troubleshooting Troubleshooting LAN Emulation Troubleshooting Pnni Links Diagnosing Congestion Troubleshooting CongestionGlobal Congestion Port Congestion Troubleshooting Congestion Function Appendix a Specifications Figure A-1 SmartSwitch 9A100 front panel ¢ %+2,%/˜96%,,%,329 Specification Value Protocol Standard Table A-4 ATM port specifications RJ-45 Pin RJ-45 Color DB-9 Pin DB-9 Description Management Protocol Supported MIBs Technical Specifications MIB, SMI, MIB Files and Internet MIB Hierarchy Appendix B Agent Support MIB, SMI, MIB Files and Internet MIB Hierarchy ZeitNet Cabletron Proprietary MIBs Relation Between Object Identifier and the Represented Value Supported SMI Formats Supported protocols Name Object Identifier Function Zeitnet Cabletron Proprietary MIB Groups MIB Exceptions SmartSwitch 9A100 MIB Support Managing the SmartSwitch 9A100 Update firmware Backup Restore Reboot Console Commands that Affect the Agent Electronic Services FAX ServiceAppendix C Technical Support Telephone Assistance Software Warranty Hardware WarrantyRepair Services Appendix D Acronyms Bootp DTE FCS Ilmi LES Netbeui PDU RMA SVC VBR/RT Acronyms SmartSwitch 9A100 User Guide Numerics Index Elan Lane Snmp Lane Pnni Non-zero values