Cinema
Digital Surround Sound Processor
TABLE OF CONTENTS
Specifications
Installation
Auto Sound Setup
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
14.LIGHTNING For added protection for the unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges
IMPORTANT SAFETY INSTRUCTIONS
26.FCC INFORMATION FOR USER
THANK YOU
WELCOME
Congratulations on becoming a Cinema 11 owner
The Cinema 11 offers
PRODUCT FEATURES
WELCOME
UNPACKING AND INSTALLATION
FORMAT DESCRIPTIONS
Warranty Card
WELCOME
WELCOME
The advantages of discrete multi-channelsystems over matrix are well known. But even in homes equipped for discrete multi-channel,there remains a need for high-qualitymatrix decoding. This is because of the large library of matrix surround motion pictures available on disc, VHS Hi Fi tape, and analog Stereo television broadcasts. The typical matrix decoder of today derives a center channel and a mono surround channel from two-channelmatrix stereo material. It is better than a simple matrix in that it includes steering logic to improve separation, but because of its mono, band-limitedsurround it can be disappointing to users accustomed to discrete multi-channelsound
All trademarks belong to their original owners
WELCOME
DTS 96/24 offers the following
About Dolby Pro Logic
SPECIFICATIONS
AUDIO INPUTS / AUDIO OUTPUTS
ANALOG AUDIO SECTION
Audio Inputs
XLR Pin Configuration Pin 1 Ground
DIGITAL AUDIO
MAIN PATH
Channel Separation 89 dB 1 kHz
ZONE 2 PATHS
CONTROL
AM Tuner
FM Tuner
Trigger Outputs
POWER REQUIREMENTS
SPECIFICATIONS
1.POWER
4.PRESET
5.PRESET
CONTROLS AND DISPLAYS
11.MASTER VOLUME KNOB
12.INFRARED RECEIVING SENSOR WINDOW
13.ALPHANUMERIC DISPLAY
14.NAVIGATION / ENTER
7.AC INLET CONNECTOR
REAR PANEL
1.ANALOG AUDIO IN INPUT 1 XLR L + R
2.ANALOG AUDIO IN INPUTS 2 THROUGH 8 RCA
10.AUTO SETUP MIC-IN
11.RS-232PORT
12.SYSTEM-LINKPORT
13.ZONE 2 DIGITAL AUDIO OUT TOSLINK OPTICAL
REMOTE CONTROL
CONTROLS AND DISPLAYS
CONTROLS AND DISPLAYS
15.BRIGHT Press this button to change the brightness of the display. Off, Low, Medium, High
ZONE 2 REMOTE CONTROL
CONTROLS AND DISPLAYS
LOCATION
INSTALLATION
GETTING STARTED
SECOND ZONE ZONE
CONNECTING A MULTI CHANNEL POWER AMPLIFIER
INSTALLATION
POWER CONTROL CONNECTIONS
POWER CONNECTION
INSTALLATION
REMOTE CONTROL
HOW TO PERFORM AUTO SOUND SETUP
AUTO SOUND SETUP
5.Speaker Check
8.Set Balance
7.Set Distance
AUTO SOUND SETUP
11.Set Speaker Phase
9.Set Room EQ
10.Set Crossover Points
AUTO SOUND SETUP
AUTO SOUND SETUP
Inphase
MANUAL SOUND SETUP
SET DISTANCE
Setting the Speaker Distance Delays
MANUAL SOUND SETUP
SET BALANCE
MANUAL SOUND SETUP
SET CROSSOVER POINTS
Setting the Speaker Crossover Points
MANUAL SOUND SETUP
SET ACOUSTIC CALIBRATION ROOM EQ
Setting the Acoustic Calibration Room EQ manually
MANUAL SOUND SETUP
MANUAL SOUND SETUP
3. Press the
SETUP MENU
Better sounds using SET SPEAKER PHASE
Setting the speaker phase manually
INPUT
SETUP MENU
SETUP MENU Input To change input names
SET ANALOG IN LEVEL SETTINGS
SET ANALOG IN CONFIG
To set Analog IN Level
SETUP MENU
RADIO
To set Analog in Config
SETUP MENU
SETUP MENU
Use the
Listening to the Radio
Manual tuning
SETUP MENU
SETUP MENU
Connection Chart
Set Up the AM and FM Antenna
To set ZONE 2 volume
ZONE
To set Zone 2 input
SETUP MENU
To set PASSWORD
AV SYNC Delay
OTHER
SETUP MENU
Bright
Edit Custom Name
To set IR Controls
SETUP MENU
To set RESTORE DEFAULT
To set TRIGGERS
To set AUTO INPUT SEEK
To set Late Mode for Dolby Digital
SERVICE AND CARE
CARE AND CLEANING
FACTORY SERVICE
NON-WARRANTYREPAIRS
UNITED STATES LIMITED WARRANTY
WARRANTY DISCLAIMER
EXCLUSIVE REMEDY
INTERNATIONAL PURCHASERS Export markets
CARY AUDIO DESIGN
o o o o o o o o o o o o o o o o o o o