Manuals / Cary Audio Design / Home Audio / Home Theater System

Cary Audio Design Cinema 11 owner manual Controls And Displays

Models: Cinema 11

1 48

Page 20

15.BRIGHT: Press this button to change the brightness of the display. (Off, Low, Medium, High)

CONTROLS AND DISPLAYS

14.LATE (for Dolby Digital only): Cycles through the various night dynamic range compression modes. (Full, Half, No compression)

15.BRIGHT: Press this button to change the brightness of the display. (Off, Low, Medium, High)

16.FM MODE: Press this button to select the audio stereo mode or monaural mode when listening to FM broadcasts. (mono/auto stereo)

17.STATION CALL: These buttons are used to preset the desired broadcasting stations.

18.BAND (FM/AM): Press this button to switch between FM and AM frequency band reception.

19.POWER ON: Press this button to turn the Cinema 11 ON.

Page 20

Image 20

Cary Audio Design Cinema 11 owner manual Controls And Displays

Contents

Cinema Digital Surround Sound ProcessorTABLE OF CONTENTS SpecificationsInstallation Auto Sound SetupIMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 14.LIGHTNING For added protection for the unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surgesIMPORTANT SAFETY INSTRUCTIONS 26.FCC INFORMATION FOR USERCongratulations on becoming a Cinema 11 owner WELCOMETHANK YOU WELCOME PRODUCT FEATURESThe Cinema 11 offers UNPACKING AND INSTALLATION FORMAT DESCRIPTIONSWarranty Card WELCOMEWELCOME The advantages of discrete multi-channelsystems over matrix are well known. But even in homes equipped for discrete multi-channel,there remains a need for high-qualitymatrix decoding. This is because of the large library of matrix surround motion pictures available on disc, VHS Hi Fi tape, and analog Stereo television broadcasts. The typical matrix decoder of today derives a center channel and a mono surround channel from two-channelmatrix stereo material. It is better than a simple matrix in that it includes steering logic to improve separation, but because of its mono, band-limitedsurround it can be disappointing to users accustomed to discrete multi-channelsoundAll trademarks belong to their original owners WELCOMEDTS 96/24 offers the following About Dolby Pro LogicSPECIFICATIONS AUDIO INPUTS / AUDIO OUTPUTSANALOG AUDIO SECTION Audio InputsXLR Pin Configuration Pin 1 Ground DIGITAL AUDIOMAIN PATH Channel Separation 89 dB 1 kHzZONE 2 PATHS CONTROLAM Tuner FM TunerSPECIFICATIONS POWER REQUIREMENTSTrigger Outputs 1.POWER 4.PRESET5.PRESET CONTROLS AND DISPLAYS11.MASTER VOLUME KNOB 12.INFRARED RECEIVING SENSOR WINDOW13.ALPHANUMERIC DISPLAY 14.NAVIGATION / ENTER7.AC INLET CONNECTOR REAR PANEL1.ANALOG AUDIO IN INPUT 1 XLR L + R 2.ANALOG AUDIO IN INPUTS 2 THROUGH 8 RCA10.AUTO SETUP MIC-IN 11.RS-232PORT12.SYSTEM-LINKPORT 13.ZONE 2 DIGITAL AUDIO OUT TOSLINK OPTICALREMOTE CONTROL CONTROLS AND DISPLAYSCONTROLS AND DISPLAYS 15.BRIGHT Press this button to change the brightness of the display. Off, Low, Medium, HighZONE 2 REMOTE CONTROL CONTROLS AND DISPLAYSGETTING STARTED INSTALLATIONLOCATION INSTALLATION CONNECTING A MULTI CHANNEL POWER AMPLIFIERSECOND ZONE ZONE POWER CONTROL CONNECTIONS POWER CONNECTIONINSTALLATION REMOTE CONTROL5.Speaker Check AUTO SOUND SETUPHOW TO PERFORM AUTO SOUND SETUP AUTO SOUND SETUP 7.Set Distance8.Set Balance 11.Set Speaker Phase 9.Set Room EQ10.Set Crossover Points AUTO SOUND SETUPAUTO SOUND SETUP InphaseMANUAL SOUND SETUP MANUAL SOUND SETUP Setting the Speaker Distance DelaysSET DISTANCE SET BALANCE MANUAL SOUND SETUPMANUAL SOUND SETUP Setting the Speaker Crossover PointsSET CROSSOVER POINTS MANUAL SOUND SETUP Setting the Acoustic Calibration Room EQ manuallySET ACOUSTIC CALIBRATION ROOM EQ MANUAL SOUND SETUP 3. Press theSETUP MENU Better sounds using SET SPEAKER PHASESetting the speaker phase manually INPUTSETUP MENU SETUP MENU Input To change input namesSET ANALOG IN LEVEL SETTINGS SET ANALOG IN CONFIGTo set Analog IN Level SETUP MENUSETUP MENU To set Analog in ConfigRADIO SETUP MENU Use theSETUP MENU Manual tuningListening to the Radio Set Up the AM and FM Antenna Connection ChartSETUP MENU To set ZONE 2 volume ZONETo set Zone 2 input SETUP MENUTo set PASSWORD AV SYNC DelayOTHER SETUP MENUBright Edit Custom NameTo set IR Controls SETUP MENUTo set RESTORE DEFAULT To set TRIGGERSTo set AUTO INPUT SEEK To set Late Mode for Dolby DigitalSERVICE AND CARE CARE AND CLEANINGFACTORY SERVICE NON-WARRANTYREPAIRSUNITED STATES LIMITED WARRANTY WARRANTY DISCLAIMEREXCLUSIVE REMEDY INTERNATIONAL PURCHASERS Export marketsCARY AUDIO DESIGN o o o o o o o o o o o o o o o o o o o