Manuals / Cary Audio Design / Home Audio / Home Theater System

Cary Audio Design Cinema 11 Set Analog In Level Settings, Set Analog In Config, Setup Menu

Models: Cinema 11

1 48

Download 48 pages 61.14 Kb

Page 37

SET ANALOG IN LEVEL SETTINGS

SETUP MENU

SET ANALOG IN LEVEL SETTINGS

This adjustment can be used to adjust 2-channel analog audio input levels for a selected input. Despite attempts at standardization, analog sources still have a wide range of input levels. To compensate for this, the Cinema 11 allows independent input level adjustment for each of the stereo analog audio input connectors. Input level adjustment is not available for the 7.1 channel analog audio input connector.

NOTE: The following selected menus appear on the Cinema 11 Display.

SETUP MENU

Input

To set Analog IN Level:

1.Press the SETUP button to enter the SETUP MENU. The SETUP MENU / SPEAKER appears.

2. Press the

button until INPUT is selected.

The SETUP MENU/ INPUT menu appears.

3. Press the ENTER button to enter the CHANGE INPUT NAMES setup menu.

4. Press the

button until SET ANALOG IN LEVEL is selected.

5. Press the ENTER button to enter the INPUT 1 level adjustment menu.

6. Use the

and

buttons to adjust the level of the INPUT 1.

You can adjust the selected channel level in 1.0 dB steps across a range of -18dB to +12dB.

7. Press the

button when you have made a selection.

Repeat steps 6 for the INPUT 2, INPUT 3, INPUT 4, INPUT 5, INPUT 6, INPUT 7 and INPUT 8.

8. Press the

button to select BACK and press the ENTER to return to the SETUP MENU,

or press the SETUP button to exit the SETUP MENU.

SET ANALOG IN CONFIG

The Cinema 11 allows analog sources to select bypass mode or DSP mode. When you select the BYPASS mode, the Cinema 11 passes analog input signals directly to the main audio output connectors. When you select DSP mode, the Cinema 11 sends analog input signals through A/D conversion and internal processing before passing them to the main audio output connectors. This allows analog sources to use bass management, speaker crossovers, speaker distance calibration, and Room EQ.

36

Image 37

Cary Audio Design Cinema 11 Set Analog In Level Settings, Set Analog In Config, To set Analog IN Level, Setup Menu

Contents

Digital Surround Sound Processor CinemaSpecifications TABLE OF CONTENTSInstallation Auto Sound SetupIMPORTANT SAFETY INSTRUCTIONS 14.LIGHTNING For added protection for the unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges IMPORTANT SAFETY INSTRUCTIONS26.FCC INFORMATION FOR USER IMPORTANT SAFETY INSTRUCTIONSTHANK YOU WELCOMECongratulations on becoming a Cinema 11 owner The Cinema 11 offers PRODUCT FEATURESWELCOME FORMAT DESCRIPTIONS UNPACKING AND INSTALLATIONWarranty Card WELCOMEThe advantages of discrete multi-channelsystems over matrix are well known. But even in homes equipped for discrete multi-channel,there remains a need for high-qualitymatrix decoding. This is because of the large library of matrix surround motion pictures available on disc, VHS Hi Fi tape, and analog Stereo television broadcasts. The typical matrix decoder of today derives a center channel and a mono surround channel from two-channelmatrix stereo material. It is better than a simple matrix in that it includes steering logic to improve separation, but because of its mono, band-limitedsurround it can be disappointing to users accustomed to discrete multi-channelsound WELCOMEWELCOME All trademarks belong to their original ownersDTS 96/24 offers the following About Dolby Pro LogicAUDIO INPUTS / AUDIO OUTPUTS SPECIFICATIONSANALOG AUDIO SECTION Audio InputsDIGITAL AUDIO XLR Pin Configuration Pin 1 GroundMAIN PATH Channel Separation 89 dB 1 kHzCONTROL ZONE 2 PATHSAM Tuner FM TunerTrigger Outputs POWER REQUIREMENTSSPECIFICATIONS 4.PRESET 1.POWER5.PRESET CONTROLS AND DISPLAYS12.INFRARED RECEIVING SENSOR WINDOW 11.MASTER VOLUME KNOB13.ALPHANUMERIC DISPLAY 14.NAVIGATION / ENTERREAR PANEL 7.AC INLET CONNECTOR1.ANALOG AUDIO IN INPUT 1 XLR L + R 2.ANALOG AUDIO IN INPUTS 2 THROUGH 8 RCA11.RS-232PORT 10.AUTO SETUP MIC-IN12.SYSTEM-LINKPORT 13.ZONE 2 DIGITAL AUDIO OUT TOSLINK OPTICALCONTROLS AND DISPLAYS REMOTE CONTROL15.BRIGHT Press this button to change the brightness of the display. Off, Low, Medium, High CONTROLS AND DISPLAYSCONTROLS AND DISPLAYS ZONE 2 REMOTE CONTROLLOCATION INSTALLATIONGETTING STARTED SECOND ZONE ZONE CONNECTING A MULTI CHANNEL POWER AMPLIFIERINSTALLATION POWER CONNECTION POWER CONTROL CONNECTIONSINSTALLATION REMOTE CONTROLHOW TO PERFORM AUTO SOUND SETUP AUTO SOUND SETUP5.Speaker Check 8.Set Balance 7.Set DistanceAUTO SOUND SETUP 9.Set Room EQ 11.Set Speaker Phase10.Set Crossover Points AUTO SOUND SETUPInphase AUTO SOUND SETUPMANUAL SOUND SETUP SET DISTANCE Setting the Speaker Distance DelaysMANUAL SOUND SETUP MANUAL SOUND SETUP SET BALANCESET CROSSOVER POINTS Setting the Speaker Crossover PointsMANUAL SOUND SETUP SET ACOUSTIC CALIBRATION ROOM EQ Setting the Acoustic Calibration Room EQ manuallyMANUAL SOUND SETUP 3. Press the MANUAL SOUND SETUPBetter sounds using SET SPEAKER PHASE SETUP MENUSetting the speaker phase manually INPUTSETUP MENU Input To change input names SETUP MENUSET ANALOG IN CONFIG SET ANALOG IN LEVEL SETTINGSTo set Analog IN Level SETUP MENURADIO To set Analog in ConfigSETUP MENU Use the SETUP MENUListening to the Radio Manual tuningSETUP MENU SETUP MENU Connection ChartSet Up the AM and FM Antenna ZONE To set ZONE 2 volumeTo set Zone 2 input SETUP MENUAV SYNC Delay To set PASSWORDOTHER SETUP MENUEdit Custom Name BrightTo set IR Controls SETUP MENUTo set TRIGGERS To set RESTORE DEFAULTTo set AUTO INPUT SEEK To set Late Mode for Dolby DigitalCARE AND CLEANING SERVICE AND CAREFACTORY SERVICE NON-WARRANTYREPAIRSWARRANTY DISCLAIMER UNITED STATES LIMITED WARRANTYEXCLUSIVE REMEDY INTERNATIONAL PURCHASERS Export marketso o o o o o o o o o o o o o o o o o o CARY AUDIO DESIGN