Cinema
Digital Surround Sound Processor
Installation
TABLE OF CONTENTS
Specifications
Auto Sound Setup
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
14.LIGHTNING For added protection for the unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges
IMPORTANT SAFETY INSTRUCTIONS
26.FCC INFORMATION FOR USER
WELCOME
THANK YOU
Congratulations on becoming a Cinema 11 owner
PRODUCT FEATURES
The Cinema 11 offers
WELCOME
Warranty Card
UNPACKING AND INSTALLATION
FORMAT DESCRIPTIONS
WELCOME
WELCOME
The advantages of discrete multi-channelsystems over matrix are well known. But even in homes equipped for discrete multi-channel,there remains a need for high-qualitymatrix decoding. This is because of the large library of matrix surround motion pictures available on disc, VHS Hi Fi tape, and analog Stereo television broadcasts. The typical matrix decoder of today derives a center channel and a mono surround channel from two-channelmatrix stereo material. It is better than a simple matrix in that it includes steering logic to improve separation, but because of its mono, band-limitedsurround it can be disappointing to users accustomed to discrete multi-channelsound
DTS 96/24 offers the following
All trademarks belong to their original owners
WELCOME
About Dolby Pro Logic
ANALOG AUDIO SECTION
SPECIFICATIONS
AUDIO INPUTS / AUDIO OUTPUTS
Audio Inputs
MAIN PATH
XLR Pin Configuration Pin 1 Ground
DIGITAL AUDIO
Channel Separation 89 dB 1 kHz
AM Tuner
ZONE 2 PATHS
CONTROL
FM Tuner
POWER REQUIREMENTS
Trigger Outputs
SPECIFICATIONS
5.PRESET
1.POWER
4.PRESET
CONTROLS AND DISPLAYS
13.ALPHANUMERIC DISPLAY
11.MASTER VOLUME KNOB
12.INFRARED RECEIVING SENSOR WINDOW
14.NAVIGATION / ENTER
1.ANALOG AUDIO IN INPUT 1 XLR L + R
7.AC INLET CONNECTOR
REAR PANEL
2.ANALOG AUDIO IN INPUTS 2 THROUGH 8 RCA
12.SYSTEM-LINKPORT
10.AUTO SETUP MIC-IN
11.RS-232PORT
13.ZONE 2 DIGITAL AUDIO OUT TOSLINK OPTICAL
REMOTE CONTROL
CONTROLS AND DISPLAYS
CONTROLS AND DISPLAYS
15.BRIGHT Press this button to change the brightness of the display. Off, Low, Medium, High
ZONE 2 REMOTE CONTROL
CONTROLS AND DISPLAYS
INSTALLATION
LOCATION
GETTING STARTED
CONNECTING A MULTI CHANNEL POWER AMPLIFIER
SECOND ZONE ZONE
INSTALLATION
INSTALLATION
POWER CONTROL CONNECTIONS
POWER CONNECTION
REMOTE CONTROL
AUTO SOUND SETUP
HOW TO PERFORM AUTO SOUND SETUP
5.Speaker Check
7.Set Distance
8.Set Balance
AUTO SOUND SETUP
10.Set Crossover Points
11.Set Speaker Phase
9.Set Room EQ
AUTO SOUND SETUP
AUTO SOUND SETUP
Inphase
MANUAL SOUND SETUP
Setting the Speaker Distance Delays
SET DISTANCE
MANUAL SOUND SETUP
SET BALANCE
MANUAL SOUND SETUP
Setting the Speaker Crossover Points
SET CROSSOVER POINTS
MANUAL SOUND SETUP
Setting the Acoustic Calibration Room EQ manually
SET ACOUSTIC CALIBRATION ROOM EQ
MANUAL SOUND SETUP
MANUAL SOUND SETUP
3. Press the
Setting the speaker phase manually
SETUP MENU
Better sounds using SET SPEAKER PHASE
INPUT
SETUP MENU
SETUP MENU Input To change input names
To set Analog IN Level
SET ANALOG IN LEVEL SETTINGS
SET ANALOG IN CONFIG
SETUP MENU
To set Analog in Config
RADIO
SETUP MENU
SETUP MENU
Use the
Manual tuning
Listening to the Radio
SETUP MENU
Connection Chart
SETUP MENU
Set Up the AM and FM Antenna
To set Zone 2 input
To set ZONE 2 volume
ZONE
SETUP MENU
OTHER
To set PASSWORD
AV SYNC Delay
SETUP MENU
To set IR Controls
Bright
Edit Custom Name
SETUP MENU
To set AUTO INPUT SEEK
To set RESTORE DEFAULT
To set TRIGGERS
To set Late Mode for Dolby Digital
FACTORY SERVICE
SERVICE AND CARE
CARE AND CLEANING
NON-WARRANTYREPAIRS
EXCLUSIVE REMEDY
UNITED STATES LIMITED WARRANTY
WARRANTY DISCLAIMER
INTERNATIONAL PURCHASERS Export markets
CARY AUDIO DESIGN
o o o o o o o o o o o o o o o o o o o