User prompt appears | Cisco Systems Cisco 3600 instruction

Chapter 3 Installing the Router

Configuring the Router

!

interface FastEthernet0/0 no shutdown

media-type 100BaseX half-duplex

ip address 172.1.2.3 255.255.0.0

!

interface FastEthernet0/1 shutdown

no ip address

!

end

Step 12 Respond to the following prompts. Select [2] to save the initial configuration.:

[0]Go to the IOS command prompt without saving this config.

[1]Return back to the setup without saving this config.

[2]Save this configuration to nvram and exit.

Enter your selection [2]: 2

Building configuration...

Use the enabled mode 'configure' command to modify this configuration.

Press RETURN to get started!

Step 13 The user prompt appears:

3600>

After you complete the initial configuration tasks, your Cisco router is ready to configure for specific functions. For configuration procedures, refer to the Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers or the Cisco IOS software configuration documentation. You can access these documents on Cisco.com and on the Documentation CD-ROM.

Cisco 3600 Series Routers Hardware Installation Guide

3-56	OL-2056-05

Image 106

Cisco Systems Cisco 3600 manual User prompt appears

Contents

Cisco 3600 Series Routers Hardware Installation Guide Corporate Headquarters Cisco 3600 Series Routers Hardware Installation Guide N T E N T S Creating a Site Log Connecting Routers to the Cisco Redundant Power System Troubleshooting A-1 Preface Objectives Conventions AudienceOrganization Chapter Title Description Safety Warnings Bewaar Deze Instructies Warnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla Sicurezza Aviso Instruções Importantes DE Segurança Guarde Estas Instruções GEM Disse Anvisninger Xiii Related Documentation Cisco Product Document Title Duration of Hardware Warranty Cisco 90-Day Limited Hardware Warranty TermsReplacement, Repair, or Refund Policy for Hardware Cisco.com To Receive a Return Materials Authorization RMA NumberObtaining Documentation Documentation CD-ROM Ordering Documentation Documentation FeedbackObtaining Technical Assistance Cisco TAC Website Opening a TAC Case TAC Case Priority Definitions Obtaining Additional Publications and Information Hardware Features Overview of Cisco 3600 Series Routers Cisco Front Panel of the Cisco 3640 Router Front Panel of the Cisco 3660 Router Modules and Interface Cards Cisco 3662 Router with Two Fast Ethernet Interfaces Description Specification Memory Installation DocumentationMemory Specifications Memory 55 KB Slot Numbering Interface NumberingCisco 3620 and Cisco 3640 Interfaces Unit Numbering Voice Interface Numbering Cisco 3631 InterfacesWAN and LAN Interface Numbering Interface Numbering-Example Cisco 3660 Interfaces Cisco 3660 Slot Numbers System Specifications Regulatory Compliance and Safety Information document that Cisco 3631 Router System Specifications Cisco 3640 Router System Specifications Regulatory Compliance OL-2056-05 Safety Recommendations Safety with Electricity Preventing Electrostatic Discharge Damage Power Supply Considerations General Site Requirements Site Configuration Site Environment Equipment Racks Installation Checklist Task Verified by Date Creating a Site Log Inspecting the Router Tools and Equipment for Installation and Maintenance Console Port Connections Console and Auxiliary Port ConsiderationsAuxiliary Port Connections Preparing to Connect to a Network Ethernet Connections Serial Connections Configuring Serial ConnectionsToken Ring Connections Serial DTE or DCE Devices Distance Limitations Signaling Standards SupportedDevice Type Gender Typical Devices EIA/TIA-232 Isdn BRI ConnectionsAsynchronous/Synchronous Serial Module Baud Rates Distance EIA-530 Distance Rate bps Feet Meters 56-K/Switched-56-kbps DSU/CSU Connections Low-Capacitance Cable Installing the Router Installing Modules, Interface Cards, and Power Supplies Setting the Chassis on a Desktop Installing the ChassisRack-Mounting the Chassis Right Attaching Brackets to the Router Cisco 3640 Rack-Mount Brackets Front-Panel-Forward Installation Use two screws on each side 17327 Rear-Panel-Forward Installation Four screws are required on each side 82808 Center-Mount Installation 22 Cisco 3660 Center-Mount Bracket Attachment Mounting the Router in the Rack Inch rack 24-inch rack 26 Mounting the Cisco 3631 Router 19-Inch Rack 28 Mounting the Cisco 3660 Router 19-Inch Rack Attaching Wall-Mount Brackets to the Router Wall-Mounting the Cisco 3620 RouterAttaching Rubber Feet to the Router Mounting the Router on the Wall Installing Chassis Ground Connection Cisco 3620 and Cisco 3640 Chassis Ground Connection Mounting Screws Power supply Bracket NEBS-Compliant Ground Lug Attachment on a Cisco 3640 Router Ring terminal attached to a bracket Power supply Ring terminal Cisco 3631 Chassis Ground Connection Ground lug attachment Cisco 3660 Chassis Ground Connection 103013 Connecting Routers to a DC-Input Power Supply Power ConnectionsConnecting Routers to AC Power 15A, 120VAC 10A, 240VAC. Statement DC Wiring Requirements DC Input DC Input Wire Size 43 DC Power Connections for Cisco 3620 Routers Typical DC Input Wiring the DC-Input Power Supply in Cisco 3631 RoutersOvercurrent 45 DC Power Connections for -DC Input to Cisco 3631 Routers Wiring the DC-Input Power Supply in Cisco 3660 Routers 47 Wire Routing and Attachment for Cisco 3631 Routers Wire Termination Safety Ground Overcurrent DC Input Wire Size Method Protection Return Safety ground Wire management bracket Connecting Routers to the Cisco Redundant Power System Connecting WAN, LAN, and Voice Cables Ports and Cabling Port or Connection Port type, color Connected to Cable T1/E1 WAN Connecting WAN, LAN, and Voice Cables Without Chassis Shield Connections for Cisco 3660 Routers LAN, WAN, and voice cables Power wires 54 Removing Panels from Chassis Shield 55 Cables Routed Through Openings in the Chassis Shield Connecting to a Console Terminal or Modem 56 Cables Routed Through the Chassis Cutout Connecting to the Console Port 57 Connecting a Console Terminal to a Cisco 3620 Router 58 Connecting a Console Terminal to a Cisco 3631 Router Connecting to the Auxiliary Port 60 Connecting a Console Terminal to a Cisco 3660 Router Modem Modem cable AUX port Connector RJ-45 RJ-45-to-RJ-45 rollover cable Identifying a Rollover Cable 65 Identifying a Rollover Cable Checklist for Power Up Powering Up the RouterFront Panel Indicators Power-Up Procedure Cisco 3620 series and Cisco 3640 series Configuring the Router Initial Configuration Using SDM Initial Configuration Using the Setup Command Facility Summary of the available interfaces is displayed User prompt appears Initial Configuration Using the CLI Manual Configuration Enter privileged Exec mode OL-2056-05 Troubleshooting Isolating Problems Troubleshooting the Power and Cooling Systems Environmental Reporting Features Troubleshooting Modules, Cables, and Connections Reading Front-Panel LEDs Figure A-1 Cisco 3620 Router Front-Panel LEDs Figure A-2 Cisco 3640 Router Front-Panel LEDs Color Description Color Power Supply StatusColor RPS Status Front-Panel LEDs on Cisco 3631 Routers LED Rear-Panel LEDs on Cisco 3631 Routers Reading Rear-Panel LEDsColor Status Rear-Panel LEDs on Cisco 3660 Routers System Error Messages Cisco 3600 Series Error Messages Message Cisco 3660 Error Messages LED Type LED Color Message Fan Cage in Cisco 3660 Routers hardware configuration note Cisco 3600 Series Routers hardware configuration note PS1, PS2 Amber Recovering a Lost Password Using the ROM Monitor Entering ROM Monitor Mode ROM Monitor Commands Enter ROM Monitor Mode by Using the reload Command Command abc ROM Monitor Syntax Conventions Router Management Commands ROM Monitor Command DescriptionsBoot Commands in the ROM Monitor Entering Boot Commands Informational Commands in the ROM Monitor Other Useful ROM Monitor Commands Debugging Commands Configuration Register Commands Modifying the Configuration Register in Menu Mode Description and Options of the xmodem Command Recovering Cisco IOS Software ImagesConsole Requirements Procedure for the xmodem Command Configuration Register Configuration Register Settings Changing Configuration Register Settings Bit Number Hexadecimal Meaning Router# config-register 0xvalue Configuring the Boot Field Boot Field Meaning Bit Address net host Baud Bit Enabling Booting from Flash Memory Router# configure Symbols IN-2 IN-3 IN-4 IN-5 IN-6