Document Contents | Cisco Systems GRP-B instruction

Gigabit Route Processor

Installation and Configuration Note

Product Numbers: GRP-B=, GRP=

Document Order Number: DOC-784339=

This hardware installation and configuration note describes the Gigabit Route Processor (GRP), the route processor for use in Cisco 12000 Series Routers.

Document Contents

Following are the sections in this document:

•Important Information, page 2

•Product Overview, page 3

•Preparing for Installation, page 10

•Replacing a GRP, page 14

•GRP Boot Process Overview, page 24

•Starting the System and Observing Initial Conditions, page 24

•Verifying Interface Status, page 27

•Configuring the Ethernet Interface, page 28

•Implementing Additional Configuration and Maintenance Tasks, page 30

•Obtaining Documentation, page 53

•Documentation Feedback, page 54

•Obtaining Technical Assistance, page 54

•Obtaining Additional Publications and Information, page 55

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Copyright © 1997-2002. Cisco Systems, Inc. All rights reserved.

Image 1

Cisco Systems GRP-B manual Gigabit Route Processor Installation and Configuration Note, Document Contents

Contents

Document Contents Gigabit Route Processor Installation and Configuration Note Router Information Important InformationSupported Platforms GRP Redundancy Cisco IOS Software Requirements Product OverviewRelated Documentation GRP Functions Cisco IOS Software GRP Components GRP Horizontal Orientation Type Memory ComponentsQuantity Description Location Flash Memory Sram System Status LEDs Soft Reset SwitchStatus LEDs Display LEDs Asynchronous Serial Ports Flash Card SlotsEthernet Port Safety Guidelines Preparing for InstallationTranslated Safety Warnings and Agency Approvals FCC Class a Compliance Electromagnetic Compatibility Regulatory StatementsCanada Europe EU Preparing for Installation Working with Electrical Equipment Preventing Electrostatic DischargeClass a Notice for Korea Required Tools and Parts Replacing a GRPRemoving a GRP Shows the ejector levers To remove a GRP, follow these steps Turn off system power Installing a GRP Console Port Pin Signal Direction Description Connecting to the Console Port Connecting to the Ethernet Port Connecting to the Auxiliary PortSignal Direction Description Ethernet Interface Receptacles, Cables, and Pinouts RJ-45 Receptacle and Plug Horizontal Orientation Pin Description MII Connections Pin Signal Input Output Input/Output Description RJ-45 Ethernet Interface Cable Connection Procedure Connecting MII or RJ-45 Cables to GRP Vertical Orientation Starting the System and Observing Initial Conditions GRP Boot Process Overview LED Display Description Processor Starting the System and Observing Initial Conditions Verifying Interface Status GRP LEDs Partial Front Panel View Configuring the Ethernet Interface Using Configuration Mode to Configure the Ethernet Interface Implementing Additional Configuration and Maintenance Tasks Configuring the Software Configuration Register Boot Field Description Boot Field Settings and the boot CommandBit Hexadecimal Description Changing Configuration Register Settings Action/File Name Bit Configuration Register Bit Meanings Baud Bit Bit Address net host Flash Disks and Flash Memory Cards in the GRP Installing and Removing Flash Memory Card or Flash Disk Formatting a Flash Memory Card or Flash Disk ATA Flash Disk Boot Image Support Requirements Router# format slot0 Software Commands Associated with Flash Memory Specifying Cisco IOS Image Used to Boot the System Router# squeeze slot0 Enabling Booting from Flash Memory Router# copy tftpmyfile1 slot0myfile1 Copying Files to Flash Memory Router# copy tftpnew.image slot0new.image Router# copy slot1image.new slot0image.new Router# config t Routerconfig# no boot system Router# copy startup-config slot0myfile2 Use the copy running-config slot0filename command as follows Recovering Lost Password Initialize the router by entering the i command as follows Locations of GRP Memory Components Upgrading GRP Memory MEM-GRP/LC-64=2 Removing DIMMs Using Dimm Socket Release Lever to Remove DIMMs Handling a Dimm Installing New DIMMs Obtaining Documentation Checking the Dimm InstallationCisco.com Obtaining Technical Assistance Documentation FeedbackOrdering Documentation Cisco TAC Website Opening a TAC Case Obtaining Additional Publications and InformationTAC Case Priority Definitions Obtaining Additional Publications and Information 78-4339-09