Manuals / Brands / Computer Equipment / Switch / Cisco Systems / Computer Equipment / Switch

Cisco Systems IE 3000 Series, IEM30004PC Attaching the Power Converter to the Switch

1 170

Download 170 pages, 9.64 Mb

2-45

Cisco IE 3000 Switch Hardware Installation Guide

OL-13017-01

Chapter 2 Switch Installation

Connecting the Switch to the Power Converter

Attaching the Power Converter to the Switch

Follow these directions to connect the power converter to the switch:

Step 1 Remove the left side panel of the switch by firmly grasping both sides of it in the middle and pulling it

outward. If necessary, use a screwdriver to open the side panel. See Figure 2-38.

Figure 2-38 Opening the Left Side Panel of the Switch

Step 2 Push the upper modules latches (at the top of the switch and the power converter) up and the lower

module latches (at the bottom of the switch and the power converter) down. See Figure 2-39.

Figure 2-39 Pushing the Module Latches Up and Positioning the Hardware

202295

202296

Contents

Main Page CONTENTS Page Page Page Page Page Preface Audience Purpose Conventions Related Publications Obtaining Documentation, Obtaining Support, and Security Guidelines Overview Overview Switch Models Front-Panel Description Page Page 10/100 Ports Dual-Purpose Ports 100BASE-FX Ports Power and Relay Connector Console Port LEDs Page Setup LED System LED Alarm LED Power Status LED 10/100 Port Status LEDs 100Base-FX Port Status LEDs Dual-Purpose Port LEDs Compact Flash Memory Card 41 2 3 Rear-Panel Description Power Converter (Optional) Management Options Network Configurations Page Switch Installation Preparing for Installation 2-2 Warnings Installation Guidelines Environment and Enclosure Guidelines: Other Guidelines Page Verifying Package Contents Adding Modules to the Switch Expansion Module Configurations Page Page Connecting Modules Page Installing or Removing the Compact Flash Memory Card Verifying Switch Operation Connecting a PC or a Terminal to the Console Port Connecting the Protective Ground and DC Power Grounding the Switch Page Page Wiring the DC Power Source Page Page Page Page Attach the Power and Relay Connector to the Switch 1 2 43 Running POST Power On the Switch Verify POST Results Disconnect Power Installing the Switch Installing the Switch on a DIN Rail Page Page Page Installing the Switch on the Wall 2 4 1 3 Page Installing the Switch in a Rack Page Removing the Switch from a DIN Rail or a Rack Connecting Power and Alarm Circuits Wiring the Protective Ground and DC Power Wiring the External Alarms Page Page Connecting Destination Ports Connecting to 10/100 and 10/100/1000 Ports Installing and Removing SFP Modules Installing SFP Modules into SFP Module Slots Page Removing SFP Modules from SFP Module Slots Connecting to SFP Modules Connecting to a Dual-Purpose Port Connecting to 100BASE-FX Ports Connecting the Switch to the Power Converter Attaching the Power Converter to the Switch Installing the Power Converter on a DIN Rail, Wall, or Rack Adapter Connecting the DC Power Clip Connecting the Power Converter to an AC Power Source Preparing the AC Power Cord Connecting the AC Power Cord to the Power Converter Page Page Connecting the Power Converter to a DC Power Source Page Applying Power to the Power Converter Where to Go Next Page Troubleshooting Diagnosing Problems Verify Switch POST Results Verify Switch LEDs Verify Switch Connections Bad or Damaged Cable Ethernet and Fiber Cables Link Status Transceiver Issues Port and Interface Settings Ping End Device Spanning Tree Loops Verify Switch Performance Speed, Duplex, and Autonegotiation Autonegotiation and NIC Cabling Distance How to Clear the Switch IP Address and Configuration How to Recover Passwords Finding the Switch Serial Number A Technical Specifications Page Page Page B Installation In a Hazardous Environment Preparing for Installation B-2 Warnings B-3 B-4 Statement 1082 locations. North American Hazardous Location Approval EMC Environmental Conditions for Products Installed in the European Union Installation Guidelines Environment and Enclosure Guidelines: Other Guidelines Verifying Package Contents Adding Modules to the Switch Expansion Module Configurations Page Connecting Modules Page Installing or Removing the Compact Flash Memory Card Verifying Switch Operation Connecting a PC or a Terminal to the Console Port Connecting the Protective Ground and DC Power Grounding the Switch Page Wiring the DC Power Source Page Page Page Page Attach the Power and Relay Connector to the Switch 43 1 2 Running POST Power On the Switch Verify POST Results Disconnect Power Installing the Switch Installing the Switch on a DIN Rail Page Page Page Installing the Switch on a Wall 2 4 1 3 Page Installing the Switch in a Rack Page Removing the Switch from a DIN Rail or a Rack Connecting Power and Alarm Circuits Information about the Sealed Relay Device Sealed Device: Relay Model AGN200A03, manufactured by Matsushita Electric Works Sealed Device: Relay Model B4GA003Z, manufactured by Fujitsu Takamisawa Electric Company Ltd. Wiring the Protective Ground and DC Power Wiring the External Alarms Page Connecting Destination Ports Connecting to 10/100 and 10/100/1000 Ports Installing and Removing SFP Modules Installing SFP Modules into SFP Module Slots Removing SFP Modules from SFP Module Slots Connecting to SFP Modules Connecting to a Dual-Purpose Port Page Connecting to 100BASE-FX Ports Connecting the Switch to the Power Converter Attaching the Power Converter to the Switch Page B-51 Cisco IE 3000 Switch Hardware Installation Guide OL-13017-01 Appendix B Installation In a Hazardous Environment Connecting the Switch to the Power Converter WARNING Cisco Catalyst Installing the Power Converter on a DIN Rail, Wall, or Rack Adapter Connecting the DC Power Clip Connecting the Power Converter to an AC Power Source Preparing the AC Power Cord Connecting the AC Power Cord to the Power Converter Page Page Connecting the Power Converter to a DC Power Source Page Applying Power to the Power Converter Where to Go Next Page C Cable and Connectors Connector Specifications 10/100 Ports Connecting to 10BASE-T- and 100BASE-TX-Compatible Devices C-2 Figure C-2 10/100/1000 Port Pinouts Figure C-1 10/100 Port Pinouts C-3 100BASE-FX Ports Figure C-4 Copper SFP Module RJ-45 Connector Warning Figure C-3 Fiber-Optic SFP Module LC Connector SFP Module Ports Cable and Adapter Specifications SFP Module Cable Specifications Two Twisted-Pair Cable Pinouts C-6 Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports Figure C-8 Four Twisted-Pair Crossover Cable Schematics for 10/100/1000 Ports Figure C-7 Four Twisted-Pair Straight-Through Cable Schematic for 10/100/1000 Ports C-7 Crossover Cable and Adapter Pinouts Figure C-10 Four Twisted-Pair Straight-Through Cable Schematic for 10/100/1000 Ports This section describes how to identify a crossover cable and also describes t he adapter pinouts. Identifying a Crossover Cable Figure C-9 Identifying a Crossover Cable Adapter Pinouts Page Page D Configuring the Switch with the CLI-Based Setup Program Accessing the CLI from the Console Port Entering the Initial Configuration Information IP Settings Completing the Setup Program Page Page INDEX Numerics A C D E F G I J L M N O P R S T V W