Manuals / Brands / Computer Equipment / Network Card / Cisco Systems / Computer Equipment / Network Card

Cisco Systems PA-2H Cisco 7200 Series and the Dual-Port HSSI Port Adapter 5-5

1 62

Download 62 pages, 1002.49 Kb

Cisco 7200 Series and the Dual-Port HSSI Port Adapter 5-5

Replacing a Port Adapter

Figure 5-5 Placing the Port Adapter Lever in the Locked Position (Cisco 7206 shown)

This completes the procedure for installing a new port adapter or replacing a port adapter in aCisco 7200 series router. To install the necessary cables and conﬁgure your dual-port HSSI portadapter, proceed to Chapter 7, “Cable Installation and Interface Conﬁguration.”ETHERNET 10BT

ENABLED

LINK

FAST SERIAL

ENABLEDMIILINKRJ45

FAST ETHERNET

0TOKEN RING

H6747

MII

RJ45

LINK

1O PWR

RJ-45

CPU RESET

FAST ETHERNET INPUT/OUTPUT CONTROLLERENABLEDPCMCIAEJECTSLOT 0SLOT 1FE MII

Port adapter

handle

Port adapter

lever (locked

position)

Note: This adapter installation

applies to any port or service

adapter.

Contents

Main PA-2H Dual-Port HSSI Port Adapter Installation and Configuration Page About This Manual Document Objectives Document Organization Cisco Connection Online Documentation CD-ROM If You Need More Information Page Page Page Overview Port Adapter Overview Page LEDs Receptacles, Cables, and Pinouts HSSI Interface Cable HSSI Null Modem Cable Page Preparing for Installation List of Parts and Tools Software and Hardware Requirements Safety Guidelines Safety Warnings Page Page FCC Class B Compliance VIP2 and the Dual-Port HSSI Port Adapter 3-1 VIP2 and the Dual-Port HSSI Port Adapter on each port adapters faceplate. Figure 3-1 VIP2-15 or VIP2-40 with PA-2H in Port Adapter Slot0 Page Page Installing a Port Adapter Page Page Catalyst RSM/VIP2 and the Dual-Port HSSI Port Adapter Page Installing a Port Adapter Page Page Cisco 7200 Series and the Dual-Port HSSI Port Adapter 5-1 Cisco 7200 Series and the Dual-Port HSSI Port Adapter PCMCIA ENABLED 4 3 Use the following standard procedure to remove a port adapter from a Cisco7200 series router: port adapter lever remains in the unlocked position. (See Figure 5-2.) Figure 5-2 Placing the Port Adapter Lever in the Unlocked Position (Cisco7206 shown) ETHERNET 10BT FAST SERIAL Replacing a Port Adapter Installation Overview 5-4 Figure 5-4 Aligning the Port Adapter Metal Carrier Between the Slot Guides (Cisco 7206 shown) 0 into the slot. Caution Do not slide the port adapter all the wayinto the slot until you have connected all required cables. Trying to do so will disrupt normal operation of the router. you feel the port adapters connectors seat in the midplane. Step 7 Movethe port adapter lever to the locked position. Figure 5-5 shows the port adapter lever Cisco 7200 Series and the Dual-Port HSSI Port Adapter 5-5 SLOT 1 H6747 0 RJ45 Page Cisco uBR7200 Series and the Dual-Port HSSI Port Adapter Page Page Replacing a Port Adapter Page Page Cable Installation and Interface Configuration Attaching HSSI Port Adapter Interface Cables Attaching a Null Modem Cable Conguring the HSSI Interfaces Identifying Chassis Slot, Port Adapter Slot, and HSSI Interface Port Numbers Cisco 7200 Series and Cisco uBR7200 Series Ports Cable Installation and Interface Configuration 7-5 RC RD TC TD Catalyst RSM/VIP2 Ports Conguring Interfaces Page Conguring Cyclic Redundancy Checks Checking the Conguration Using show Commands to Verify the New Interface Status Configuring the HSSI Interfaces 7-10 Cisco 7200 Series and Cisco uBR7200 Series show Commands Note For the Cisco 7206 and Cisco7206VXR router shelves, the show interfaces command Page VIP2 show Commands Cable Installation and Interface Configuration 7-13 Checking the Configuration Catalyst RSM/VIP2 show Commands Cable Installation and Interface Configuration 7-15 Checking the Configuration Page Using the ping Command