Cisco Systems UBR924 Purpose, Organization, Document Conventions

viii

CiscouBR924 Software Configuration Guide

OL-0337-05 (8/2002)

Preface

Purpose

Purpose

This configuration guide explains the initial and basic software co nfiguration procedures for the

Cisco uBR924 cable access router. This guide contains procedures for configuring the

Cisco uBR924 router for both data only operation, as well as for voice and data operation. This guide

also describes how to set up basic security, the headend interface (CMTS-to-CM), and how to use ROM

monitor.

Organization

This guide is organized into the chapters and appendixes shown in Ta ble 1, which also shows the ch anges

from the previous version of this guide:

Note For a complete list of changes in each CiscoIOS release, see the Release Notes that accompany that

release.

Document Conventions

This publication uses the following conventions:

Table1 Organization

Chapter Title Description

Changes from the Previous

Release

Chapter1Overview Provides an overview of the CiscouBR924 cable

access router and its possible configurations.

Includes features added in

Cisco IOS Release 12.1(5)T.

Chapter2 DOCSIS-Bridging

Configuration

Describes how to configure the router for its

default of DOCSIS-compliant bridging operation.

None.

Chapter3 Advanced Data-Only

Configurations

Describes how to configure the router for various

data-only configurations such as routing operation

and IPSec encryption.

None.

Chapter4 Voice over IP

Configurations

Describes how to configure the router for Voice

over IP (VoIP) traffic using either the H.323v2 or

SGCP/MGCP call control protocols.

None.

Appendix A Using Cisco IOS

Software

Describes the basics of using the Cisco IOS

command line interface (CLI).

None.

Appendix BUsing the Cable

Monitor Tool

Describes how to display diagnostic information

about the CiscouBR924 cable access router using

any web browser.

None.

Appendix C Using the ROM Monitor Describes how to use the CiscoIOS ROM

monitor.

Minor changes on entering

ROMMON mode and returning

to normal mode.

Appendix D New and Changed

Commands Reference

Lists the commands that are new to the

CiscoIOS12.1T software releases.

Includes commands added in

Cisco IOS Release 12.1(5)T.

Contents

Main Cisco uBR924 Cable Access Router Software Configuration Guide Page CONTENTS Page Page Page Preface Audience Purpose Organization Document Conventions Page x loss of data. this guide. paragraph. Acronyms and Terms Related Documentation Cisco uBR924 Cable Access Router CMTS Hardware Installation Publications Cisco IOS Publications Configuration Editor and Network Management Publications Subscriber Publications Obtaining Documentation World Wide Web Documentation CD-ROM Ordering Documentation Obtaining Technical Assistance Technical Assistance Center Documentation Feedback Page Overview Cisco IOS Software Release Feature Sets Base IP DOCSIS-Compliant Bridging Home Office (Easy IP) Value Telecommuter Performance Telecommuter Value Small and Branch Office Performance Small and Branch Office Feature Descriptions Cable Monitor Web Diagnostics Tool Cisco Cable Clock Card Support Cisco IOS Firewall DOCSIS-Compliant Bridging DOCSIS Baseline Privacy Interface Dynamic Host Configuration Protocol Server Dynamic Host Configuration Protocol Proxy Support Enhanced IP Bridging Ecosystem Gatekeeper Interoperability Enhancements Fax over IP H.323v2 (Gateway/Gatekeeper) IP Address Negotiation IPsec Network Security Layer 2 Tunneling Protocol Media Gateway Control Protocol V12.1.3T NetRanger SupportCisco IOS Intrusion Detection Network Address Translation and Port Address Translation Network Address Translation Support for NetMeeting Directory (Internet Locator Service) Quality of Service Quality of ServiceDOCSIS 1.0+ Extensions Routing Information Protocol Version 2 Secure Shell Version 1 Simple Gateway Control Protocol Triple Data Encryption Standard VPN IPsec EnhancementDynamic Crypto Map Initial Provisioning Supporting Multiple Classes of Service DOCSIS 1.0 Static Profiles DOCSIS 1.0+ and 1.1 Dynamic Profiles Creating Multiple Profiles User Registrar Modem Registrar Cisco Network Registrar Access Registrar Page DOCSIS-Bridging Configuration DHCP Server Configuration DOCSIS Configuration File Page Page Cisco IOS Software Image Cisco IOS Configuration File Using the Vendor-Specific Information Field 2-8 Sample Configuration for DOCSIS-Compliant Bridging This configuration shows the following requirements for DOCSIS-compliant br idging: Configuring the Attached CPE Devices Reconfiguring DOCSIS-Compliant Bridging Page Advanced Data-Only Configurations Data-Only Routing Page Routing with DHCP Server 3-5 NAT/PAT Configuration Page NAT/PAT Configuration with DHCP Proxy Page Using NAT and DHCP Proxy and Copying Configuration Files IPSec (56-bit) Example Page Sample Configuration 3-14 56-bit DES-CBC encryption (the default) MD5 (HMAC variant) hash algorithm Pre-shared authentication keys 768-bit Diffie-Hellman group (the default) Additional Documentation IPSec (3DES) Example L2TP Example Page 3-19 Page Voice over IP Configurations Overview Introduction Page Voice Handling Quality of Service Support H.323v2 Protocol SGCP and MGCP Protocol Stack H.323v2 Static Bridging Configuration Page 4-9 H.323v2 Static Routing Configuration 4-11 routing mode. H.323v2 Dynamic Mapping Configuration Note The Cisco uBR924 router can use H.323v2 dynamic mapping in either DOCSIS-bridging mode or Page Page Page SGCP Configuration Page 4-17 MGCP Configuration Page 4-20 Command Purpose Step22 uBR924# copy running-config startup-config Step23 uBR924# show startup-config Display the configuration file that was just created. Building configuration... 4-21 Page A Using Cisco IOS Software Accessing the Routers Command-Line Interface Connecting Using Telnet Connecting to the Console Port Understanding the Command-Line Interface Command Modes User EXEC Mode Privileged EXEC Mode Global Configuration Mode Interface Configuration Mode Context-Sensitive Help Command History Features Displaying the Command History Editing Previous Commands Command History Buffer Size Using Output Modifiers Understanding Cisco IOS Configuration Files Downloading the Configuration File Startup and Run-Time Configuration Files Displaying the Configuration Files File Format Useful Commands Page B Using the Cable Monitor Tool Enabling the Cable Monitor Configuration Modes Security Considerations Disabling the Cable Monitor Accessing the Cable Monitor Through the Cable Interface when the Cable Interface is Operational Through the Ethernet Interface when the Cable Interface is Not Operational Sample Pages Page Home Page Page Initialization Information Page Page Voice Ports Information Page CPE State Information Page Cable Interface Information Page Performance Information Page Debug Information Page Page C Using the ROM Monitor Entering the ROM Monitor Command Conventions Commands Page Page Page Page D New and Changed Commands Reference Commands Reserved for DOCSIS Use Page INDEX Symbols Numerics A D E F G H I L O P Q R U V