Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems (VIP6-80) Bottom ejector lever Processor module slot, Captive, installation, screw

Models: (VIP6-80)

1 40

Download 40 pages 44.43 Kb

Page 17

Image 17

Figure 3 shows a detail of the ejector lever mechanism on the ends of the VIP.

Figure 3 Ejector Levers and Captive Installation Screws on the VIP6-80—Vertical Orientation Shown

Bottom ejector lever

Processor module slot

Processor

module

carrier guide

Captive

installation

screw

Stop

immediately

on contact

H1482a

Proceed to either the “Removing a VIP6-80” section on page 18 to replace a VIP6-80 or to the “Installing a VIP6-80” section on page 24 to install a new VIP6-80.

To install or remove a port adapter, see the “Removing and Installing Port Adapters” section on page 19.

Versatile Interface Processor (VIP6-80) Installation and Configuration Guide

	OL-5078-01	17

Page 17

Image 17

Cisco Systems (VIP6-80) manual Bottom ejector lever Processor module slot, Captive, installation, screw, Stop, immediately

Contents

Installation Prerequisites, page ContentsIntroduction Customer Order Number DOC-7814372=Removing a VIP6-80, page Removing and Installing Port Adapters, page Guidelines for Removal and Installation, pageInstalling a VIP6-80, page Performing a Basic Configuration, page Checking the VIP6-80 Installation, page Maintenance Procedures, pageProduct Description Specifications, page System Software, page Traffic Management, page“Obtaining Documentation” section on page “Obtaining Additional Publications and Information” section on pageServices DSW Distributed SwitchingPackets Forwarding ProductLocation Memory ComponentsType SizeJumpers LEDsMicrocode ROM MonitorNumber of Port Adapter SlotsSingle or Product NumberSingle or Number ofProduct Number DescriptionSpecifications SpecificationsSystem Software DescriptionAgency Approvals, page Safety Guidelines, page Installation PrerequisitesTraffic Management Software RequirementsMicrocode Requirements Safety GuidelinesTools and Parts Required Agency ApprovalsSafety Warnings Electrical Equipment Guidelines Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage Guidelines for Removal and Installation H1355a Figure 2 Handling Interface Processors-Vertical Orientation ShownOL-5078-01 Bottom ejector lever Processor module slot installationProcessor moduleRemoving a VIP6-80 Connecting Cables to the Port Adapter, page Removing and Installing Port AdaptersTools and Parts Required, page Single-Width Port Adapter, page Dual-Width Port Adapter, pageFigure 4 Handling a Port Adapter Single-Width Port AdapterStep Figure 5 Removing and Installing a Single-Width Port AdapterStep StepDual-Width Port Adapter Step Figure 7 Removing and Installing a Dual-Width Port AdapterStep StepConnecting Cables to the Port Adapter Installing a VIP6-80Performing a Basic Configuration Verifying the Installation Checking the VIP6-80 InstallationVerifying the Installation, page Using show Commands to Verify the VIP6-80 Status, pageNote New interfaces are not available until you configure them Using show Commands to Verify the VIP6-80 Status Router# show controllers cbus Using show Commands to Display Interface InformationRouter# show controllers fastethernet 1/1/0 show controllers commandRouter# show version show diagUsing the ping Command to Verify Network Connectivity Checking the VIP6-80 Memory Upgrade, page Maintenance ProceduresSingle Line Card Reload Upgrading VIP6-80 MemoryMEM-VIP6-64M-SD= ProductDescription Removing SDRAM DIMMs Installing SDRAM DIMMs See the “Checking the VIP6-80 Installation” section on page TroubleshootingChecking the VIP6-80 Memory Upgrade Cisco.com Obtaining DocumentationDocumentation CD-ROM Ordering DocumentationDocumentation Feedback Obtaining Technical AssistanceCisco TAC Website Opening a TAC CaseTAC Case Priority Definitions Obtaining Additional Publications and InformationCopyright 2003 Cisco Systems, Inc. All rights reserved