Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems (VIP6-80) manual Single-Width Port Adapter, Handling a Port Adapter

Models: (VIP6-80)

1 40

Download 40 pages 44.43 Kb

Page 20

Figure 4 Handling a Port Adapter

Figure 4 Handling a Port Adapter

Metal carrier

Printed circuit board

H6420

Single-Width Port Adapter

Single-width port adapters occupy one of the two port adapter slots on a VIP6-80. When a single-width port adapter slot is not in use, use a blank port adapter to fill the empty slot to allow the router to conform to EMI emissions requirements and to allow proper airflow through the router. If you plan to install a new single-width port adapter in a port adapter slot that is not in use, first remove the blank port adapter.

Figure 5 describes the steps required to install a single-width port adapter.

Versatile Interface Processor (VIP6-80) Installation and Configuration Guide

20	OL-5078-01

Image 20

Cisco Systems (VIP6-80) manual Single-Width Port Adapter, Handling a Port Adapter

Contents

Contents Installation Prerequisites, pageIntroduction Customer Order Number DOC-7814372=Guidelines for Removal and Installation, page Removing a VIP6-80, page Removing and Installing Port Adapters, pageInstalling a VIP6-80, page Performing a Basic Configuration, page Checking the VIP6-80 Installation, page Maintenance Procedures, pageSpecifications, page System Software, page Traffic Management, page Product Description“Obtaining Documentation” section on page “Obtaining Additional Publications and Information” section on pageDistributed Switching Services DSWPackets Forwarding ProductMemory Components LocationType SizeLEDs JumpersMicrocode ROM MonitorPort Adapter Slots Number ofSingle or Product NumberNumber of Single orProduct Number DescriptionSpecifications SpecificationsSystem Software DescriptionInstallation Prerequisites Agency Approvals, page Safety Guidelines, pageTraffic Management Software RequirementsSafety Guidelines Microcode RequirementsTools and Parts Required Agency ApprovalsSafety Warnings Telephone Wiring Guidelines Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage Guidelines for Removal and Installation H1355a Figure 2 Handling Interface Processors-Vertical Orientation ShownOL-5078-01 installation Bottom ejector lever Processor module slotProcessor moduleRemoving a VIP6-80 Removing and Installing Port Adapters Connecting Cables to the Port Adapter, pageTools and Parts Required, page Single-Width Port Adapter, page Dual-Width Port Adapter, pageSingle-Width Port Adapter Figure 4 Handling a Port AdapterFigure 5 Removing and Installing a Single-Width Port Adapter StepStep StepDual-Width Port Adapter Figure 7 Removing and Installing a Dual-Width Port Adapter StepStep StepInstalling a VIP6-80 Connecting Cables to the Port AdapterPerforming a Basic Configuration Checking the VIP6-80 Installation Verifying the InstallationVerifying the Installation, page Using show Commands to Verify the VIP6-80 Status, pageNote New interfaces are not available until you configure them Using show Commands to Verify the VIP6-80 Status Using show Commands to Display Interface Information Router# show controllers cbusshow controllers command Router# show controllers fastethernet 1/1/0Router# show version show diagUsing the ping Command to Verify Network Connectivity Maintenance Procedures Checking the VIP6-80 Memory Upgrade, pageSingle Line Card Reload Upgrading VIP6-80 MemoryMEM-VIP6-64M-SD= ProductDescription Removing SDRAM DIMMs Installing SDRAM DIMMs See the “Checking the VIP6-80 Installation” section on page TroubleshootingChecking the VIP6-80 Memory Upgrade Obtaining Documentation Cisco.comDocumentation CD-ROM Ordering DocumentationObtaining Technical Assistance Documentation FeedbackCisco TAC Website Opening a TAC CaseObtaining Additional Publications and Information TAC Case Priority DefinitionsCopyright 2003 Cisco Systems, Inc. All rights reserved