ClearOne comm AP400 specification

rights reserved. No part of this document may

be reproduced in any form or by any means

without written permission from ClearOne

Communications, Inc. Printed in the United

States of America. ClearOne Communications,

Inc. reserves specific privileges. Information in

this document is subject to change without

notice.

AP400 Installation and

Operation Manual

ClearOne Part No. 800-150-001

July 2002 (Rev. 5.0)

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Page 2

Image 2

ClearOne comm operation manual AP400 Installation ClearOne Part No July 2002 Rev

Contents

AP400 Audio Conferencing System AP400 Installation ClearOne Part No July 2002 Rev Table of Contents Iii Appendices AP-Ware SoftwareOperation Introduction Product Overview Features Technical Support Professional Services GroupSales and Customer Service ClearOne Communications EuMEA GmbH Front panel UnpackingControls and Connections Rear panel Introduction ~ Controls and Connections Link Network Link bus Control bus Introduction ~ G-Link Networking BusLink EC Reference bus NOM Technical Services Group ~ 1-800-283-5936 USA ~ Equipment Requirements Hardware Setup AP400 installation diagram To connect the AP400 Connecting the unitInstallation ~ Hardware Setup Link connections Installation ~ Networking UnitsNetworking Units To create a G-Link network To set the device ID Mixer modeDevice IDs Device types EC reference To set mixer modeErrors LCD Programming Installation ~ LCD ProgrammingSwitching from one main menu category to another Menu trees Adjusting a value LCD menu tree Lock panel Select presetSystem parameters Set passcode Unit ID Mixer modeDevice ID Gate parameters Gate Ratio Last Mic ModeFirst mic priority Off Attenuation Hold Time To determine ambient level Decay RateManual Ambient Combination Channels Installation ~ LCD Programming RS-232 Inputs Installation ~ LCD Programming TelcoInput parameters EQ Status Phantom PowerHigh-Pass Filter Chairman Mic Inputs A-D, Telco Echo cancellerNLP adjust Subbus Output 1-4, Output A-D, Telco Output parametersRouting parameters EC reference and PA Installation ~ LCD Programming SubbusLink X-Z buses Link reference Slave unit Inputs, Outputs, ERL/TERL, and ERLE/TERLE Default MeterMeter parameters Installation ~ Worksheet 64MB RAM DescriptionAP-Ware software requirements Installing AP-Ware To install AP-Ware Front Panel Controlling the volumeTo adjust the volume Muting To mute or unmute an output Telco InterfaceTo make and disconnect a call Instructions Custom control through DB-25 port Other telco optionsControllers Operation ~ Controllers Touch panel control Appendix a Specifications Appendices This warranty is void if Appendix B Warranty and ComplianceWarranty FCC Part 68 Compliance Appendices ~ Appendix B Warranty and ComplianceFCC Part 15 Compliance Industry Canada Compliance Safety Information RS-232 COM DCE port pinout Appendix C Connector PinoutsAppendices ~ Appendix C Connector Pinouts Control/Status port pinout Appendices ~ Appendix D Accessories Appendix D AccessoriesAppendix E Serial Commands Accessory ClearOne Part Number Mref Command SyntaxError Codes Device Appendices ~ Appendix E Serial Commands Figure E.1. AP400 Serial Commands Explanation Serial Command Parameters ExplanationsAamb Return Values Device AGC CH AGCDevice AD CH= A-D BYE AmblvlBaud Chairo Dfltm DecayDial Erle ERL FPP FlowFMP Microphone gating key GainExamples Example Hold GmodeGratio Hook LMO HookdLFP LVL MEQ MasterMdmode Mline MHPMinit Mtrx MmaxMpass Input Input word assignment Return Values OutputmixOUTPUTMIXNote =NULL Mute NLPDevice Mute CH W Device NLP CH Null NOMOffa PAA Example Preset Preset Refsel Tamode RingRxrd Return Value UID TerlTerle Tout Appendix F Worksheets Figure F.1. Routing matrix worksheet Appendices ~ Appendix F Worksheets Figure F.2. Programming worksheet Figure F.3. Audio flow block diagram Index DSP Index ~ P-Z