Unpacking, Controls and Connections | ClearOne comm AP400 specs

4	Introduction ~ Unpacking

Unpacking

Ensure that the equipment shown below was received with your shipment.

ClearOne is not responsible ! for product damage incurred during shipment.

You must make claims directly with the carrier. Inspect your shipment carefully for obvious signs of damage. If the shipment appears to be damaged, retain the original boxes and packing material for inspection by the carrier. Contact your carrier immediately.

Audio Products

AP400 Audio Conferencing System

Figure 1.1. Equipment

Controls and Connections

Front panel

AB C D E FG H

Figure 1.2. Front panel controls

✍	AP-Ware software provides
	AP-Ware software provides
	complete	configuration
	capabilities for the AP400.

Please refer to the AP-Ware help file for more information.

A.LCD. The two-line, 16-character-per-line LCD display is used for AP400 setup and level adjustments in conjunction with the four associated front- panel buttons [B]. Functions that can be accessed via the front-panel LCD include setup, programming, troubleshooting, and numeric audio level and gain readouts.

B.Enter/▲▼ /ESC. These buttons are used to navigate the AP400’s menu system.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 8

ClearOne comm AP400 operation manual Unpacking, Controls and Connections, Front panel

Contents

AP400 Audio Conferencing System AP400 Installation ClearOne Part No July 2002 Rev Table of Contents Iii Appendices AP-Ware SoftwareOperation Introduction Product Overview Features Professional Services Group Sales and Customer ServiceTechnical Support ClearOne Communications EuMEA GmbH Front panel UnpackingControls and Connections Rear panel Introduction ~ Controls and Connections Link Network Link bus Introduction ~ G-Link Networking Bus Link EC Reference busControl bus NOM Technical Services Group ~ 1-800-283-5936 USA ~ Equipment Requirements Hardware Setup AP400 installation diagram To connect the AP400 Connecting the unitInstallation ~ Hardware Setup Installation ~ Networking Units Networking UnitsLink connections To create a G-Link network Mixer mode Device IDsTo set the device ID Device types EC reference To set mixer modeErrors Installation ~ LCD Programming Switching from one main menu category to anotherLCD Programming Menu trees Adjusting a value LCD menu tree Select preset System parametersLock panel Set passcode Mixer mode Device IDUnit ID Gate parameters Gate Ratio Last Mic ModeFirst mic priority Off Attenuation Hold Time Decay Rate Manual AmbientTo determine ambient level Combination Channels Installation ~ LCD Programming RS-232 Inputs Installation ~ LCD Programming TelcoInput parameters Phantom Power High-Pass FilterEQ Status Chairman Mic Echo canceller NLP adjustInputs A-D, Telco Subbus Output 1-4, Output A-D, Telco Output parametersRouting parameters EC reference and PA Installation ~ LCD Programming SubbusLink X-Z buses Link reference Slave unit Inputs, Outputs, ERL/TERL, and ERLE/TERLE Default MeterMeter parameters Installation ~ Worksheet 64MB RAM DescriptionAP-Ware software requirements Installing AP-Ware To install AP-Ware Controlling the volume To adjust the volumeFront Panel Muting Telco Interface To make and disconnect a callTo mute or unmute an output Instructions Other telco options ControllersCustom control through DB-25 port Operation ~ Controllers Touch panel control Appendix a Specifications Appendices This warranty is void if Appendix B Warranty and ComplianceWarranty FCC Part 68 Compliance Appendices ~ Appendix B Warranty and ComplianceFCC Part 15 Compliance Industry Canada Compliance Safety Information Appendix C Connector Pinouts Appendices ~ Appendix C Connector PinoutsRS-232 COM DCE port pinout Control/Status port pinout Appendix D Accessories Appendix E Serial CommandsAppendices ~ Appendix D Accessories Accessory ClearOne Part Number Command Syntax Error CodesMref Device Appendices ~ Appendix E Serial Commands Figure E.1. AP400 Serial Commands Serial Command Parameters Explanations AambExplanation Return Values AGC Device ADDevice AGC CH CH= A-D Amblvl BaudBYE Chairo Dfltm DecayDial Erle ERL FPP FlowFMP Gain ExamplesMicrophone gating key Example Gmode GratioHold Hook Hookd LFPLMO LVL MEQ MasterMdmode Mline MHPMinit Mmax MpassMtrx Input Input word assignment Return Values OutputmixOUTPUTMIXNote =NULL Mute NLPDevice Mute CH W Device NLP CH NOM OffaNull PAA Example Preset Preset Refsel Ring RxrdTamode Return Value Terl TerleUID Tout Appendix F Worksheets Figure F.1. Routing matrix worksheet Appendices ~ Appendix F Worksheets Figure F.2. Programming worksheet Figure F.3. Audio flow block diagram Index DSP Index ~ P-Z