Appendices ~ Appendix E Serial Commands | ClearOne comm AP400

Appendices ~ Appendix E: Serial Commands

45

The command string will then be explained (where necessary), followed by the

returned values and (where necessary) an example.

Figure E.1. AP400 Serial Commands

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 49

ClearOne comm operation manual Appendices ~ Appendix E Serial Commands, Figure E.1. AP400 Serial Commands

Contents

AP400 Audio Conferencing System AP400 Installation ClearOne Part No July 2002 Rev Iii Table of Contents Operation AP-Ware SoftwareAppendices Product Overview Introduction Features Sales and Customer Service Professional Services GroupTechnical Support ClearOne Communications EuMEA GmbH Controls and Connections UnpackingFront panel Introduction ~ Controls and Connections Rear panel Link bus Link Network Link EC Reference bus Introduction ~ G-Link Networking BusControl bus NOM Technical Services Group ~ 1-800-283-5936 USA ~ Equipment Requirements AP400 installation diagram Hardware Setup Installation ~ Hardware Setup Connecting the unitTo connect the AP400 Networking Units Installation ~ Networking UnitsLink connections To create a G-Link network Device IDs Mixer modeTo set the device ID Device types Errors To set mixer modeEC reference Switching from one main menu category to another Installation ~ LCD ProgrammingLCD Programming Menu trees LCD menu tree Adjusting a value System parameters Select presetLock panel Set passcode Device ID Mixer modeUnit ID Gate parameters First mic priority Last Mic ModeGate Ratio Hold Time Off Attenuation Manual Ambient Decay RateTo determine ambient level Combination Channels Installation ~ LCD Programming RS-232 Input parameters Installation ~ LCD Programming TelcoInputs High-Pass Filter Phantom PowerEQ Status Chairman Mic NLP adjust Echo cancellerInputs A-D, Telco Subbus Routing parameters Output parametersOutput 1-4, Output A-D, Telco Link X-Z buses Installation ~ LCD Programming SubbusEC reference and PA Slave unit Link reference Meter parameters Default MeterInputs, Outputs, ERL/TERL, and ERLE/TERLE Installation ~ Worksheet AP-Ware software requirements Description64MB RAM To install AP-Ware Installing AP-Ware To adjust the volume Controlling the volumeFront Panel Muting To make and disconnect a call Telco InterfaceTo mute or unmute an output Instructions Controllers Other telco optionsCustom control through DB-25 port Operation ~ Controllers Touch panel control Appendices Appendix a Specifications Warranty Appendix B Warranty and ComplianceThis warranty is void if FCC Part 15 Compliance Appendices ~ Appendix B Warranty and ComplianceFCC Part 68 Compliance Industry Canada Compliance Safety Information Appendices ~ Appendix C Connector Pinouts Appendix C Connector PinoutsRS-232 COM DCE port pinout Control/Status port pinout Appendix E Serial Commands Appendix D AccessoriesAppendices ~ Appendix D Accessories Accessory ClearOne Part Number Error Codes Command SyntaxMref Device Figure E.1. AP400 Serial Commands Appendices ~ Appendix E Serial Commands Aamb Serial Command Parameters ExplanationsExplanation Return Values Device AD AGCDevice AGC CH CH= A-D Baud AmblvlBYE Chairo Dial DecayDfltm ERL Erle FMP FlowFPP Examples GainMicrophone gating key Example Gratio GmodeHold Hook LFP HookdLMO LVL Mdmode MasterMEQ Minit MHPMline Mpass MmaxMtrx Input Input word assignment OUTPUTMIXNote OutputmixReturn Values Device Mute CH W Device NLP CH Mute NLP=NULL Offa NOMNull PAA Example Preset Refsel Preset Rxrd RingTamode Return Value Terle TerlUID Tout Figure F.1. Routing matrix worksheet Appendix F Worksheets Figure F.2. Programming worksheet Appendices ~ Appendix F Worksheets Figure F.3. Audio flow block diagram DSP Index Index ~ P-Z