Manuals / Cognitive Solutions / Computer Equipment / All in One Printer

Cognitive Solutions A776, B780 List of DH 4700 Command Descriptions, Printer Function Commands

Models: B780 A776

1 192

Download 192 pages 23.55 Kb

Page 159

List of DH 4700 Command Descriptions

Chapter 6: DH Emulation 147

List of DH 4700 Command Descriptions

The command descriptions in this section are grouped in the following categories:

·Printer Function Commands

·Print Characteristics Commands

·Graphics Commands

·Printer Status Commands

Within each group the commands are listed in numerical order according to their hexadecimal codes. Each command is described and the hexadecimal, decimal, and ASCII codes are listed.

Printer Function Commands

These commands control the following basic printer functions:

·Printing

·Feeding paper

·Moving the printhead

·Resetting the printer

The commands are listed numerically by hexadecimal code.

End of Text

Informs printer to send an acknowledge (Hexadecimal 06, Decimal 6, ASCII ACK) to the host computer after all characters have been printed and all commands performed.

Hexadecimal	Decimal	ASCII
03	3	ETX

Line Feed

Prints the data in the buffer and feeds the paper one line. The height of the line is determined by the internal DIP switch settings or by the Set Up Parameters command (19 n).

Hexadecimal	Decimal	ASCII
0A	10	LF

Vertical Tab

Prints any data in the buffer and then advances the paper .02083 inches (0.523mm).

Hexadecimal	Decimal	ASCII
0B	11	VT

Carriage Return

Prints the data in the buffer and advances the paper if Auto Line Feed is enabled either by the internal DIP switch settings or by the Set Up Parameters command (19 n). See “Chapter 3: Diagnostics and Print Test” for more information.

Hexadecimal	Decimal	ASCII
0D	13	CR

Setup Parameters

Sets temporary values for default printer parameters. N is the sum of the values for each parameter.

	Hexadecimal	Decimal	ASCII
	19 n	25 n	EM n
	Value of n
	Hexadecimal	Decimal	ASCII	Parameter	Setting
00		01	NUL	Auto Line Feed	ON
01			SOH		OFF
00		02	NUL	Characters per Line	40
	02		STX		ALT
00		0	NUL	Journal Lines/Inch	8.0
04		4	EOT		6.9
08		8	BS		6.0
	0C	12	FF		5.3
A776-PG00001 C 12/09					A776 (B780) Programming Guide

Image 159

Cognitive Solutions A776, B780 List of DH 4700 Command Descriptions, Printer Function Commands, End of Text, Line Feed

Contents

A776-PG00001 Rev. C A776 B780 Two-Color Thermal/Impact Hybrid PrinterPrinter without Imaging Printer with Imaging Programming GuideInformation to the User Contents Select B780 Slip Right Text Margin and Text Column Options A776 B780 Programming GuideSelect peripheral device for multi-drop Select receipt or slip for setting line spacingSelect paper sensors to output paper end signals Select receipt or slip for printing slip for MICR readSelect or cancel upside-down print mode Select or cancel 90 degree clockwise rotated printSelect or cancel white/black reverse print mode Select or cancel user-defined character setA776 B780 Programming Guide ContentsGraphics StatusSelect or cancel unsolicited status mode USM Set absolute vertical print position in page modeSet relative vertical print position in page mode Rules for using real-time commandsReturn segment number status of flash memory Return boot sector firmware part numberErase all flash contents except boot sector area for storing logos and user-defined charactersviii Contents Contents x Contents A776 B780 Programming GuideA776-PG00001 C 12/09 Chapter 1 About this Guide How to use this GuideWhere to find the basics Where to find advanced technical information2 Chapter 1 About this Guide A776 B780 Programming GuideA776-PG00001 C 12/09 Remote diagnostics Chapter 2 Printer Status and IndicatorsStartup Diagnostics Runtime diagnosticsMAC address Ethernet terms and default setupBootP Ethernet Terminology Ethernet Default SetupGreen slip-in light in front of the paper feed button IndicatorsMigrating from existing CognitiveTPG printers Chapter 3 Migrating to A776 and B7802A m n1 n2 d1...dn Moving from the A756 to the A776 Thermal printhead differences24 n1 n2 26 s c1 c2 n1 d1...nn dn57 nL nH Moving from the A756 to the A776 Emulation commandsMoving from the A756, A758, or A760 to the A776 Slip differences 4C nL nHSet A776 Printer Emulation A776 Emulation CommandsA776 Configuration Commands Set A776 Printer IDSelect A776 Delete Slip Trailing Spaces Option Select A776 Narrow Slip 51-column Compressed Print Option12 Chapter 3 Migrating to a new printer Select A776 First Line of Print Option in Text and Page ModeSelect A776 21 and 25-line Rotated Slip Print Options Select Cover Open OptionSelect 45/60 Column Slip Option Set Page Mode Margin Mechanical AdjustmentSet Page Mode Option to Trim Full Dots Select A776 Slip Eject OptionA776 Slip Left Margin and Print Width A776 Configurable Slip Commands A776 Double High Slip Character PrintA776 Slip Character Spacing A776 Slip Minimum UnitsMoving from A756/A758 to A776 Two-color Commands LogoEZ colorization commands A776-PG00001 C 12/09Page Migrating from the A721 7221 printer to the B780 B780 Emulation CommandsB780 Configuration Commands Set Printer ID ModeSelect DH Pitch and Rotated Text Columns Select Slip Lines per Inch18 Chapter 3 Migrating to a new printer Select B780 Map User Character Option for B780 Select Slip Right Margin in Page ModeSelect Two - Sensor Option for B780 Select Number of Lines of Validation for B780Select B780 with A776 Slip Functions Select B780 Map Logo Option for B780Select Cover Open Option for B780 Select Concurrent Print to Receipt for B780Set Page Mode Margin Mechanical Adjustment Set Page Mode Option to Trim Full DotsSelect Cover Open Option for B780 22 Chapter 3 Migrating to a new printer A776 B780 Programming GuideA776-PG00001 C 12/09 Chapter 4 Programming the Printer Overview of Printing CharacteristicsCompressed Receipt character specificationCharacter appearance StandardPrint zones for receipt station 80 mm paper Print zonesPrint zones for slip station Print Zones for Slip, Validation Rotated printing commands Chapter 5 Programming Commands Commands listed by functionPrinter actions 26 s c1 c2 Text characteristicsPrint and paper feed Vertical and horizontal positioning1F 26 s c1 c2 Graphics1D 90 m x y o p q Batch modeStatus Real-timeMacros Page modeMICR check reader commands Bar codes73 n1 n2 k Ethernet setup commandsUser data storage Flash download1D B9 s t m nL nH pL pH Image Commands1D C5 nL nH m d1-dn-1 1D B4 nL nH t0. . .tmPrinter actions Command conventionsCommand descriptions Clear printerGenerate tone Close formOpen form Perform partial knife cutSet unidirectional print on impact station Select peripheral device for multi-dropInitialize printer Set slip paper eject length1B 63 33 n Select receipt or slip for setting line spacingSelect paper sensors to output paper end signals Select receipt or slip for printing slip for MICR readEnable or disable panel button Select sensors to stop printingSet slip paper waiting time Generate pulse to open cash drawer Release PaperSet current color Select cut mode and cut paper Select slip stationSet paper type ColorPOS Set Interpretation of “Set current color” Select receipt stationPrint and carriage return Print test formPrint and feed paper one line Print and eject slipFeed n dot rows Add n extra dot rows3 extra dot rows Print and feed n lines PrintPrint and feed paper Print and reverse feed paperHorizontal tab Print and reverse feed n linesReverse feed n lines Reverse feed n dots3.33 mm 0.13” Set columnSet absolute starting position Set vertical line spacing to 1/6 inchSet vertical line spacing Set horizontal tab positionsn is always less than or equal to the Set relative print position To move to the leftTo move to the right Select justification Set left marginContinued Set horizontal and vertical minimum motion units Set printing area widthContinued Select 90 degree counter-clockwise rotated print Text characteristics commandsSelect double-wide characters Select single-wide charactersSelect pitch column width Set right-side character spacingCompressed Select or cancel user-defined character set Select print modeContinued Define user-defined character setCopy character set from ROM to RAM Select or cancel underline modeContinued Cancel user-defined characterSelect or cancel emphasized mode Select double-strikeContinued Cancel double-strikeSelect or cancel italic print Select international character setSelect character size Select or cancel 90 degree clockwise rotated printSelect or cancel upside-down print mode Select character code tableContinued Select or cancel white/black reverse print modeSet smoothing Reverse color text mode ColorPOSText strike-through mode ColorPOS Select font ID numberSelect font style number Select superscript or subscript modes Save font ID number as default font at power upDownload font Download font listThe bytes are printed down and across each cell See the illustration Define extended user-defined character setSelect active user-defined character set Any invalid byte s, c1, c2, n1, n2 aborts the commandContinued Select bit image modeDownload BMP logo Graphicsn1 + 256 × n2 Print advanced raster graphicsAdvanced raster graphics is not available in page mode 8-dot single-densitySelect the current logo downloaded bit image Select double-density graphicsPrint Flash Logo Define Flash LogosPrint downloaded bit image Define downloaded bit imagePrint raster monochrome graphics ColorPOS Print raster color graphics ColorPOSDownload logo image ColorPOS GS 0x87 m Monochrome shade mode ColorPOSColor shade mode ColorPOS GS 0x86 mMerge watermark mode ColorPOS Logo print with color plane swap ColorPOSApply shading to logo ColorPOS Form and merge real-time surround graphic ColorPOS Background logo print mode ColorPOS Save graphics buffer as logo ColorPOS Apply margin message mode ColorPOS Shade and store logo ColorPOS1D 99 l m n o Set temporary max target speed Logo print with knife cutSet LogoEZ colorization ColorPOS ExampleContinued Continued Skip “s” feed paper dot rows 15 s commandExample ExampleContinued Set LogoEZ attribute mapping ColorPOSattribute mapped 80 Chapter 5 Programming commands Original attribute mapped tableContinued m bit onConvert 6-dots/mm bitmap to 8-dots/mm bitmap Enable constant speed logosStatus Status command introductionTransmit peripheral device status Batch modeTransmit paper sensor status Transmit printer IDContinued Transmits the printer ID specified by n as follows Transmit printer ID, remote diagnostics extension Preforms the remote diagnostic function specified by nThe table that follows describes the variables Continued Continued Transmit statusContinued Send printer software version Real-time commandsMoving data through the buffer Rules for using real-time commandsPreferred implementation Alternate implementationBusy line and fault conditions Real-time status transmissionContinued 2 = Transmit RS-232C Busy Status Bit Status Hex Decimal Function 92 Chapter 5 Programming commands3 = Transmit error status ContinuedFunction Chapter 5 Programming commands 93 4 = Transmit receipt paper statusStatus DecimalReal-time request to printer Real-time commands disable Real-time printer status transmissionExceptions Select or cancel unsolicited status mode USM Unsolicited status modeOff/On Hex Chapter 5 Programming commands 97 First Byte printer InformationSecond byte error information ContinuedBit Off/On Hex Chapter 5 Programming commandsContinued Third byte paper sensor informationRecognizing data from the printer Print bar code Select printing position of HRI charactersSelect pitch of HRI characters Select bar code heightContinued The command is only valid at the beginning of a lineSet GS1 DataBar formerly RSS parameters ASCII Print GS1 DataBar formerly RSS, data length specifiedPrint GS1 DataBar formerly RSS, null terminated Chapter 5 Programming commands 103Begin multiple barcodes one line Print multiple barcodesSample symbol description Select PDF 417 parametersContinued Select bar code width Page modeSets the bar code width to n dots Character Size Slip page mode considerationsSuggested command sequence to print bank check Page sizeSlip Page Mode Disabled Print and return to standard mode Page mode configurationsSlip Page Mode Improved Slip Page Mode EnabledSelect page mode Select print direction in page mode Select standard mode1B 57 n1, n2 ...n8 Set print area in page modeContinued ESC W n1, n2 ...n829 92 nL nH Set absolute vertical print position in page modeSet relative vertical print position in page mode ContinuedContinued Select or cancel macro definitionExecute macro MacrosMICR commands MICR readingRead MICR data and transmit Define parsing format, do not save permanently MICR parsingTransmit last MICR read Define parsing format, save in NVRAMOther parameters ESC w p 18 A CR Sample parsing formatsChapter 5 Programming commands 117 ContinuedContinued All characters in the transit number Field separatorCheck serial number Example Loading the exception tableException table entry format which writes the two byte word n1n2 to word k in NVRAMExample Maintaining the exception tableWrite to user data storage User data storageSelect memory type SRAM/flash Read from user data storageRead from non-volatile memory Write to non-volatile memory NVRAM1D 22 Flash memory user sectors allocationExpanded flash memory allocation ContinuedSelect flash area for storing logos and user-defined characters Erase user flash sectorContinued Continued User storage status ColorPOSFlash download allocation commandsGet firmware CRC Return boot sector firmware part numberReturn segment number status of flash memory memory sector to downloadDownload to active flash sector Erase all flash contents except boot sectorReturn main program flash CRC Erase selected flash sectorSet Net Mask Reset firmwareRestore default settings Set IP addressBootP Set GatewaySet raw TCPIP port Telnet DaemonDHCP auto-configuration Inactivity timeoutKeep-alive pings Value Imaging CommandsCalibrate Scanner Hexadecimal ID B0 Parameters NoneHexadecimal 1D B1 m n Configure/Change Image Transmission PortSet Top Entry Startup Delay Set Image Format PropertiesDefinition Configure Binarization Methods and AttributesMethod ValueDefinition Define/Update Application Tag ValuesDecimal Value Return NoneHexadecimal 1D B7 Attach Scan Application TagsReturn Imager Status Hexadecimal 1D B6 Parameters NoneDefinition Real-Time Imager StatusHexadecimal 10 04 Parameters None ValueHexadecimal 10 05 Parameters None Return None Real-Time Error StatusReal-Time Cancel Image Transmission Wait for Scan & Optionally TransmitMeaning ValueDefinition DecimalTransmit Image ValueDefinition Meaning ValueDefinition DecimalDefinition Eject from ScannerHexadecimal 1D BA p ValueGet Buffered Image Attributes Free ImageFree Imager Buffering Get Buffered Image ListHexadecimal 1D C6 m n Parameters Configure Scan OptionsConfigure Max Scan Width & Height Transmit Printer Type Extended Existing CommandHexadecimal Code List of DH 4700 Emulation CommandsCommand Name Chapter 6 DH emulation for B780Hexadecimal Code List of DH emulation Commands continuedCommand Name 146 Chapter 6 DH emulationEnd of Text List of DH 4700 Command DescriptionsPrinter Function Commands Setup ParametersSelf Test Reset PrinterCash Drawer Document Clamp OpenDownload Clamp DelayDocument Clamp Close Form EjectBuffer Clear Print Characteristics CommandsPrint Speed Buffered ValidateCharacter Set Double-High Font Underline PrintUnderline Off Double-High OffContinued Graphics CommandsGraphics Graphics 5 DotStatus-Firmware Printer Status CommandsStatus 3 Bit Status 6 BitChapter 6 DH Emulation 155 A776-PG00001 C 12/09A776 B780 Programming Guide 27 m a0 a1 a2 d1…dm Commands listed by hexadecimal codeAppendix A 26 s c1 c2Page CommandAppendix A Commands by hexadecimal code Code hexadecimal73 n1 n2 k 158 Appendix A Commands by hexadecimal codeCommand Code hexadecimal71 a b c d e fL fH 5E r t m6B m nL nH d1... dn 6B n d11D C5 nL nH m d1-dn-1 8B n m o90 m x y o p q 9A n m o08 04 n1 n2 n3 n4 08 01 n1 n2 n3 n408 02 n1 n2 n3 n4 08 03 n1 n2 n3 n4Appendix B Resident Character Sets Code Page 437 USA776-PG00001 C 12/09 Code page 737 Greek Appendix B Resident Character SetsA776 B780 Programming Guide Code page 850 Multilingual 164 Appendix B Resident Character SetsA776-PG00001 C 12/09 Code Page 852 Slavic A776-PG00001 C 12/09A776 B780 Programming Guide Code Page 857 Turkish 166 Appendix B Resident Character SetsA776-PG00001 C 12/09 Code page 858 with Eurosymbol A776-PG00001 C 12/09A776 B780 Programming Guide Code page 860 Portugese 168 Appendix B Resident Character SetsA776-PG00001 C 12/09 Code page 862 Hebrew A776-PG00001 C 12/09A776 B780 Programming Guide Code page 863 French Canadian 170 Appendix B Resident Character SetsA776-PG00001 C 12/09 Code page 865 Nordic A776-PG00001 C 12/09A776 B780 Programming Guide Code page 866 Cyrillic 172 Appendix B Resident Character SetsA776-PG00001 C 12/09 Code page 1252 Windows Latin A776-PG00001 C 12/09A776 B780 Programming Guide Page Appendix C Electronic Journal 1F 03 18 01 n Auto Journal Mode via Configuration CommandAuto Journal Mode via Runtime Command 1F 0A C1 - Enable 1F 0A C2 - DisableException Conditions in Auto Journal Mode Journal RAM bufferJournal Flash buffer 1F 0A C4 Print Journal Printing and Erasing the Journal Flash BufferOperator Activation of Journal Print and Erase 1F 0A C3 Clear Journal178 Appendix C Electronic Journal 1F 0A C5 Return Journal Status1F 0A C6 Return Journal Flash Size 1F 0A C7 Write Journal RAM Data to FlashPage A776-PG00001 Rev. C 12/09