Manuals / Cognitive Solutions / Computer Equipment / All in One Printer

Cognitive Solutions B780 manual LogoEZ colorization commands, A776-PG00001 C 12/09, Page

Models: B780 A776

1 192

Download 192 pages 23.55 Kb

Page 28

Image 28

16 Chapter 3: Migrating to a new printer

LogoEZ® colorization commands

Hexadecimal		ASCII	Discription	Page
1F	03 16 f s p/r t	US ETX SYN f s p/r t	Set colorization	77
1F	03 17 a m s	US ETX ETB a m s	Set attribute mapping	79

Note: The new CognitiveTPG LogoEZ® colorization utility provides you a fast and easy way do get basic two-color and logos on your receipt without having to enter commands. Check out the CognitiveTPG Web site at www.CognitiveTPG.com.

A776 (B780) Programming Guide

A776-PG00001 C 12/09

Page 28

Image 28

Cognitive Solutions B780 manual LogoEZ colorization commands, A776-PG00001 C 12/09, Page

Contents

A776 B780 Two-Color Thermal/Impact Hybrid Printer Printer without Imaging Printer with ImagingProgramming Guide A776-PG00001 Rev. CInformation to the User Contents A776 B780 Programming Guide Select B780 Slip Right Text Margin and Text Column OptionsSelect receipt or slip for setting line spacing Select paper sensors to output paper end signalsSelect receipt or slip for printing slip for MICR read Select peripheral device for multi-dropSelect or cancel 90 degree clockwise rotated print Select or cancel white/black reverse print modeSelect or cancel user-defined character set Select or cancel upside-down print modeContents GraphicsStatus A776 B780 Programming GuideSet absolute vertical print position in page mode Set relative vertical print position in page modeRules for using real-time commands Select or cancel unsolicited status mode USMReturn boot sector firmware part number Erase all flash contents except boot sectorarea for storing logos and user-defined characters Return segment number status of flash memoryviii Contents Contents A776 B780 Programming Guide x ContentsA776-PG00001 C 12/09 How to use this Guide Where to find the basicsWhere to find advanced technical information Chapter 1 About this GuideA776 B780 Programming Guide 2 Chapter 1 About this GuideA776-PG00001 C 12/09 Chapter 2 Printer Status and Indicators Startup DiagnosticsRuntime diagnostics Remote diagnosticsEthernet terms and default setup BootPEthernet Terminology MAC addressEthernet Default Setup Indicators Green slip-in light in front of the paper feed buttonChapter 3 Migrating to A776 and B780 Migrating from existing CognitiveTPG printersMoving from the A756 to the A776 Thermal printhead differences 24 n1 n226 s c1 c2 n1 d1...nn dn 2A m n1 n2 d1...dnMoving from the A756 to the A776 Emulation commands Moving from the A756, A758, or A760 to the A776 Slip differences4C nL nH 57 nL nHA776 Emulation Commands A776 Configuration CommandsSet A776 Printer ID Set A776 Printer EmulationSelect A776 Narrow Slip 51-column Compressed Print Option Select A776 Delete Slip Trailing Spaces OptionSelect A776 First Line of Print Option in Text and Page Mode Select A776 21 and 25-line Rotated Slip Print OptionsSelect Cover Open Option 12 Chapter 3 Migrating to a new printerSet Page Mode Margin Mechanical Adjustment Set Page Mode Option to Trim Full DotsSelect A776 Slip Eject Option Select 45/60 Column Slip OptionA776 Configurable Slip Commands A776 Double High Slip Character Print A776 Slip Character SpacingA776 Slip Minimum Units A776 Slip Left Margin and Print WidthMoving from A756/A758 to A776 Two-color Commands A776-PG00001 C 12/09 LogoEZ colorization commandsPage B780 Emulation Commands B780 Configuration CommandsSet Printer ID Mode Migrating from the A721 7221 printer to the B780Select Slip Lines per Inch Select DH Pitch and Rotated Text Columns18 Chapter 3 Migrating to a new printer Select Slip Right Margin in Page Mode Select Two - Sensor Option for B780Select Number of Lines of Validation for B780 Select B780 Map User Character Option for B780Select B780 Map Logo Option for B780 Select Cover Open Option for B780Select Concurrent Print to Receipt for B780 Select B780 with A776 Slip FunctionsSet Page Mode Option to Trim Full Dots Set Page Mode Margin Mechanical AdjustmentSelect Cover Open Option for B780 A776 B780 Programming Guide 22 Chapter 3 Migrating to a new printerA776-PG00001 C 12/09 Overview of Printing Characteristics Chapter 4 Programming the PrinterReceipt character specification Character appearanceStandard CompressedPrint zones Print zones for receipt station 80 mm paperPrint zones for slip station Print Zones for Slip, Validation Rotated printing commands Commands listed by function Chapter 5 Programming CommandsPrinter actions Text characteristics Print and paper feedVertical and horizontal positioning 26 s c1 c2Graphics 1F 26 s c1 c2Batch mode StatusReal-time 1D 90 m x y o p qPage mode MICR check reader commandsBar codes MacrosEthernet setup commands User data storageFlash download 73 n1 n2 kImage Commands 1D C5 nL nH m d1-dn-11D B4 nL nH t0. . .tm 1D B9 s t m nL nH pL pHCommand conventions Command descriptionsClear printer Printer actionsClose form Open formPerform partial knife cut Generate toneSelect peripheral device for multi-drop Initialize printerSet slip paper eject length Set unidirectional print on impact stationSelect receipt or slip for setting line spacing Select paper sensors to output paper end signalsSelect receipt or slip for printing slip for MICR read 1B 63 33 nSelect sensors to stop printing Enable or disable panel buttonSet slip paper waiting time Release Paper Generate pulse to open cash drawerSet current color Select slip station Select cut mode and cut paperSet paper type ColorPOS Select receipt station Set Interpretation of “Set current color”Print test form Print and feed paper one linePrint and eject slip Print and carriage returnAdd n extra dot rows Feed n dot rows3 extra dot rows Print Print and feed paperPrint and reverse feed paper Print and feed n linesPrint and reverse feed n lines Reverse feed n linesReverse feed n dots Horizontal tabSet column Set absolute starting positionSet vertical line spacing to 1/6 inch 3.33 mm 0.13”Set horizontal tab positions Set vertical line spacingn is always less than or equal to the To move to the left Set relative print positionTo move to the right Set left margin Select justificationContinued Set printing area width Set horizontal and vertical minimum motion unitsContinued Text characteristics commands Select double-wide charactersSelect single-wide characters Select 90 degree counter-clockwise rotated printSet right-side character spacing Select pitch column widthCompressed Select print mode Select or cancel user-defined character setDefine user-defined character set ContinuedSelect or cancel underline mode Copy character set from ROM to RAMCancel user-defined character Select or cancel emphasized modeSelect double-strike ContinuedCancel double-strike Select or cancel italic printSelect international character set ContinuedSelect or cancel 90 degree clockwise rotated print Select or cancel upside-down print modeSelect character code table Select character sizeSelect or cancel white/black reverse print mode ContinuedReverse color text mode ColorPOS Set smoothingSelect font ID number Text strike-through mode ColorPOSSelect font style number Save font ID number as default font at power up Download fontDownload font list Select superscript or subscript modesDefine extended user-defined character set Select active user-defined character setAny invalid byte s, c1, c2, n1, n2 aborts the command The bytes are printed down and across each cell See the illustrationSelect bit image mode Download BMP logoGraphics ContinuedPrint advanced raster graphics Advanced raster graphics is not available in page mode8-dot single-density n1 + 256 × n2Select double-density graphics Print Flash LogoDefine Flash Logos Select the current logo downloaded bit imageDefine downloaded bit image Print downloaded bit imagePrint raster color graphics ColorPOS Print raster monochrome graphics ColorPOSDownload logo image ColorPOS Monochrome shade mode ColorPOS Color shade mode ColorPOSGS 0x86 m GS 0x87 mLogo print with color plane swap ColorPOS Merge watermark mode ColorPOSApply shading to logo ColorPOS Form and merge real-time surround graphic ColorPOS Save graphics buffer as logo ColorPOS Background logo print mode ColorPOS Shade and store logo ColorPOS Apply margin message mode ColorPOS1D 99 l m n o Logo print with knife cut Set temporary max target speedExample Set LogoEZ colorization ColorPOSContinued Skip “s” feed paper dot rows 15 s command ExampleExample ContinuedSet LogoEZ attribute mapping ColorPOS Continued80 Chapter 5 Programming commands Original attribute mapped table Continuedm bit on attribute mappedEnable constant speed logos Convert 6-dots/mm bitmap to 8-dots/mm bitmapStatus command introduction Transmit peripheral device statusBatch mode StatusTransmit printer ID Transmit paper sensor statusContinued Transmits the printer ID specified by n as follows Preforms the remote diagnostic function specified by n Transmit printer ID, remote diagnostics extensionThe table that follows describes the variables Continued Transmit status ContinuedContinued Real-time commands Send printer software versionRules for using real-time commands Preferred implementationAlternate implementation Moving data through the bufferReal-time status transmission Busy line and fault conditionsContinued 92 Chapter 5 Programming commands 3 = Transmit error statusContinued 2 = Transmit RS-232C Busy Status Bit Status Hex Decimal FunctionChapter 5 Programming commands 93 4 = Transmit receipt paper status StatusDecimal FunctionReal-time request to printer Real-time printer status transmission Real-time commands disableExceptions Unsolicited status mode Select or cancel unsolicited status mode USMChapter 5 Programming commands 97 First Byte printer Information Second byte error informationContinued Off/On HexChapter 5 Programming commands ContinuedThird byte paper sensor information Bit Off/On HexRecognizing data from the printer Select printing position of HRI characters Select pitch of HRI charactersSelect bar code height Print bar codeThe command is only valid at the beginning of a line ContinuedSet GS1 DataBar formerly RSS parameters Print GS1 DataBar formerly RSS, data length specified Print GS1 DataBar formerly RSS, null terminatedChapter 5 Programming commands 103 ASCIIPrint multiple barcodes Begin multiple barcodes one lineSelect PDF 417 parameters Sample symbol descriptionContinued Page mode Select bar code widthSets the bar code width to n dots Slip page mode considerations Suggested command sequence to print bank checkPage size Character SizePage mode configurations Slip Page Mode ImprovedSlip Page Mode Enabled Slip Page Mode Disabled Print and return to standard modeSelect page mode Select standard mode Select print direction in page modeSet print area in page mode ContinuedESC W n1, n2 ...n8 1B 57 n1, n2 ...n8Set absolute vertical print position in page mode Set relative vertical print position in page modeContinued 29 92 nL nHSelect or cancel macro definition Execute macroMacros ContinuedMICR reading MICR commandsRead MICR data and transmit MICR parsing Transmit last MICR readDefine parsing format, save in NVRAM Define parsing format, do not save permanentlyOther parameters Sample parsing formats Chapter 5 Programming commands 117Continued ESC w p 18 A CRAll characters in the transit number Field separator ContinuedCheck serial number Loading the exception table Exception table entry formatwhich writes the two byte word n1n2 to word k in NVRAM ExampleMaintaining the exception table Write to user data storageUser data storage ExampleRead from user data storage Read from non-volatile memoryWrite to non-volatile memory NVRAM Select memory type SRAM/flashFlash memory user sectors allocation Expanded flash memory allocationContinued 1D 22Erase user flash sector Select flash area for storing logos and user-defined charactersContinued User storage status ColorPOS Continuedallocation commands Flash downloadReturn boot sector firmware part number Return segment number status of flash memorymemory sector to download Get firmware CRCErase all flash contents except boot sector Return main program flash CRCErase selected flash sector Download to active flash sectorReset firmware Restore default settingsSet IP address Set Net MaskSet Gateway Set raw TCPIP portTelnet Daemon BootPInactivity timeout DHCP auto-configurationKeep-alive pings Imaging Commands Calibrate ScannerHexadecimal ID B0 Parameters None ValueConfigure/Change Image Transmission Port Set Top Entry Startup DelaySet Image Format Properties Hexadecimal 1D B1 m nConfigure Binarization Methods and Attributes MethodValue DefinitionDefine/Update Application Tag Values Decimal ValueReturn None DefinitionAttach Scan Application Tags Return Imager StatusHexadecimal 1D B6 Parameters None Hexadecimal 1D B7Real-Time Imager Status Hexadecimal 10 04 Parameters NoneValue DefinitionReal-Time Error Status Real-Time Cancel Image TransmissionWait for Scan & Optionally Transmit Hexadecimal 10 05 Parameters None Return NoneValue DefinitionDecimal MeaningValue Transmit ImageDefinition Value DefinitionDecimal MeaningEject from Scanner Hexadecimal 1D BA pValue DefinitionFree Image Free Imager BufferingGet Buffered Image List Get Buffered Image AttributesConfigure Scan Options Configure Max Scan Width & HeightTransmit Printer Type Extended Existing Command Hexadecimal 1D C6 m n ParametersList of DH 4700 Emulation Commands Command NameChapter 6 DH emulation for B780 Hexadecimal CodeList of DH emulation Commands continued Command Name146 Chapter 6 DH emulation Hexadecimal CodeList of DH 4700 Command Descriptions Printer Function CommandsSetup Parameters End of TextReset Printer Cash DrawerDocument Clamp Open Self TestClamp Delay Document Clamp CloseForm Eject DownloadPrint Characteristics Commands Print SpeedBuffered Validate Buffer ClearCharacter Set Underline Print Underline OffDouble-High Off Double-High FontGraphics Commands GraphicsGraphics 5 Dot ContinuedPrinter Status Commands Status 3 BitStatus 6 Bit Status-FirmwareA776-PG00001 C 12/09 Chapter 6 DH Emulation 155A776 B780 Programming Guide Commands listed by hexadecimal code Appendix A26 s c1 c2 27 m a0 a1 a2 d1…dmCommand Appendix A Commands by hexadecimal codeCode hexadecimal Page158 Appendix A Commands by hexadecimal code CommandCode hexadecimal 73 n1 n2 k5E r t m 6B m nL nH d1... dn6B n d1 71 a b c d e fL fH8B n m o 90 m x y o p q9A n m o 1D C5 nL nH m d1-dn-108 01 n1 n2 n3 n4 08 02 n1 n2 n3 n408 03 n1 n2 n3 n4 08 04 n1 n2 n3 n4Code Page 437 US Appendix B Resident Character SetsA776-PG00001 C 12/09 Appendix B Resident Character Sets Code page 737 GreekA776 B780 Programming Guide 164 Appendix B Resident Character Sets Code page 850 MultilingualA776-PG00001 C 12/09 A776-PG00001 C 12/09 Code Page 852 SlavicA776 B780 Programming Guide 166 Appendix B Resident Character Sets Code Page 857 TurkishA776-PG00001 C 12/09 A776-PG00001 C 12/09 Code page 858 with EurosymbolA776 B780 Programming Guide 168 Appendix B Resident Character Sets Code page 860 PortugeseA776-PG00001 C 12/09 A776-PG00001 C 12/09 Code page 862 HebrewA776 B780 Programming Guide 170 Appendix B Resident Character Sets Code page 863 French CanadianA776-PG00001 C 12/09 A776-PG00001 C 12/09 Code page 865 NordicA776 B780 Programming Guide 172 Appendix B Resident Character Sets Code page 866 CyrillicA776-PG00001 C 12/09 A776-PG00001 C 12/09 Code page 1252 Windows LatinA776 B780 Programming Guide Page 1F 03 18 01 n Auto Journal Mode via Configuration Command Auto Journal Mode via Runtime Command 1F 0A C1 - Enable1F 0A C2 - Disable Appendix C Electronic JournalJournal RAM buffer Exception Conditions in Auto Journal ModeJournal Flash buffer Printing and Erasing the Journal Flash Buffer Operator Activation of Journal Print and Erase1F 0A C3 Clear Journal 1F 0A C4 Print Journal1F 0A C5 Return Journal Status 1F 0A C6 Return Journal Flash Size1F 0A C7 Write Journal RAM Data to Flash 178 Appendix C Electronic JournalPage A776-PG00001 Rev. C 12/09