WARNING: The Cooling Unit must be electrically grounded to avoid possible fatal electrical shock or serious injury to the operator. A green ground wire is provided inside electrical box to connect power circuit ground wire which electrically grounds the Cooling Unit.

2.60HZ Cooling Unit

Connect 208/230VAC Single Phase 60Hz electrical power circuit with a 40-amp minimum rated disconnect switch (not provided) fused at 40-amps (maximum) or circuit connected through an equivalent HACR circuit breaker to electrical wires inside electrical handy box on back of cooling unit. DO NOT CONNECT ELECTRICAL POWER TO COOLING UNIT AT THIS TIME.

COOLING UNIT MUST BE PROPERLY GROUNDED, POWER CIRCUIT MUST BE MADE UP OF COPPER CONDUCTORS, AND ALL WIRING MUST CONFORM TO NATIONAL AND LOCAL ELECTRICAL CODES.

50HZ Cooling Unit

Connect 208/230VAC Single Phase 50Hz electrical power circuit with a 40-amp minimum rated disconnect switch (not provided) fused at 40-amps (maximum) or circuit connected through an equivalent HACR circuit breaker to electrical wires inside electrical handy box on back of cooling unit. DO NOT CONNECT ELECTRICAL POWER TO COOLING UNIT AT THIS TIME.

COOLING UNIT MUST BE PROPERLY GROUNDED, POWER CIRCUIT MUST BE MADE UP OF COPPER CONDUCTORS, AND WIRING MUST CONFORM TO APPLICABLE ELECTRICAL CODES.

CONNECTING ELECTRICAL POWER CIRCUIT TO REMOTE CONDENSER COIL AND FAN ASS’Y (IF APPLICABLE) see Figures 6 and 15)

CAUTION: The Cooling Unit refrigeration system is cooled by a Remote Condenser Coil and Fan Assembly (P/N 309602000) that is authorized by IMI Cornelius Inc. Use of an unauthorized Remote Condenser Coil and Fan Assembly will automatically void the

Cooling Unit factory warranty.

Remote Condenser Coil and Fan Assembly (P/N 309602000)

NOTE: Electrical power circuit may be connected to the Remote Condenser Coil and Fan Assembly (P/N 309602000) in two ways. The preferred way is to draw electrical power from the Cooling Unit contactor which allows the Remote Condenser Coil and Fan assembly to operate only when the Cooling Unit refrigeration system is operating. The optional way is to connect a separate electrical power circuit (independent of the cooling unit) through an appropriately rated and fused disconnect switch or an equivalent HACR circuit breaker which allows the Remote Condenser Coil and Fan Assembly to operate at all times (independent of Cooling Unit operation).

Connect and route electrical power circuit cable from Remote Condenser Coil and Fan Assembly through fuse box (not provided), fused at 15-amps (maximum) down to Cooling Unit location. REMOTE CONDENSER COIL AND FAN ASSEMBLY MUST BE PROPERLY GROUNDED, POWER CIRCUIT MUST BE MADE UP OF COPPER CONDUCTORS, AND ALL WIRING MUST CONFORM TO NATIONAL AND LOCAL ELECTRICAL CODES.

A.Remove four screws securing electrical control box to Cooling Unit back panel, (see Figure 6) then pull control box out for access to contactor inside box.

B.Route Remote Condenser Coil and Fan Assembly power cable electrical wires through electrical handy box on back of Cooling Unit to inside of electrical control box.

C.Connect Remote Condenser Coil and Fan Assembly power cable electrical wires to T1 and T2 terminals on contactor inside Cooling Unit electrical control box.

300381000

8

Page 12 Page 14
Page 13
Image 13
Cornelius 000, 10 installation manual Cooling Unit factory warranty
Page 12 Page 14

000, 10 specifications

Cornelius 10,000 PLUS is a pioneering innovation in the beverage dispensing industry, designed to cater to the evolving needs of commercial establishments. This advanced system combines state-of-the-art technology with user-friendly features, making it a standout choice for restaurants, cafes, and bars aiming to enhance their beverage service.

One of the main features of the Cornelius 10,000 PLUS is its impressive capacity. With the ability to dispense a wide variety of beverages, including soft drinks, cocktails, and craft beers, the system supports a large volume of service, perfect for high-demand environments. The modular design allows for easy expansion, enabling businesses to add additional flavors or beverages as needed without major overhauls.

The technology behind the Cornelius 10,000 PLUS is equally impressive. It utilizes advanced cooling technology to ensure that beverages are served at the optimal temperature, enhancing the customer experience. The integrated touchless dispensing mechanism minimizes waste and ensures a hygienic experience, addressing growing concerns about cleanliness in food service environments. This technology also improves speed, allowing staff to serve customers more efficiently.

Another key characteristic of the Cornelius 10,000 PLUS is its digital integration capabilities. The system can be connected to a central management platform that tracks sales, inventory levels, and maintenance needs in real-time. This allows operators to optimize their beverage offerings based on customer preferences and reduces downtime through proactive maintenance alerts.

In addition to its performance features, the Cornelius 10,000 PLUS is designed with sustainability in mind. The system employs energy-efficient practices, reducing its environmental footprint while lowering operational costs. The materials used in construction are durable yet eco-friendly, ensuring longevity and less waste.

Overall, the Cornelius 10,000 PLUS stands out as an essential tool for any business looking to elevate its beverage service. With its combination of high capacity, cutting-edge technology, and sustainability features, it not only meets the demands of today’s fast-paced service environments but also positions establishments for future growth and success.
Top Page Image Contents