3.Lower Cooling Unit into operating position to complete seal from unit base to floor. Apply additional sealant around bottom of base. Seal must have a minimum radius of 1/2-inch to prevent cracks and crevices and to ensure a complete seal.

4.Route Cooling Unit water tank overflow hose to permanent floor drain.

5.Seal area around overflow hose where they exit from unit using permagum sealant or equivalent.

PREPARING COOLING UNIT FOR OPERATION

1.Make sure plug in end of Cooling Unit water tank drain hose is secure.

2.Open shutoff valve in plain water inlet supply line. Due to slow water fill rate of water level float control, water tank may be hand filled until water runs out of water tank overflow hose. CLEAN LOW-MINERAL-CONTENT WATER MUST BE USED WHERE A LOCAL WATER PROBLEM EXIST.

3.Adjust primary CO2 regulator (see Figure 2) on CO2 cylinder to a minimum nominal setting of 120-psi or 24-psi higher than highest setting required by the secondary CO2 regulators. Loosen CO2 regulator adjusting screw locknut. Turn adjusting screw to the right (clockwise) until regulator gage registers nominal 120-psi, then tighten adjusting screw locknut.

4.Adjust carbonators secondary CO2 regulator (see Figure 2) to a nominal 90-psi. Loosen CO2 regulator adjusting screw locknut. Turn adjusting screw to the right (clockwise) until regulator gage registers nominal

90-psi, then tighten adjusting screw lock nut. CO2 PRESSURE TO CARBONATORS MUST NOT EXCEED 120-PSIG.

CAUTION: Before starting refrigeration system, Hydro Boostâ coil must be completely flooded with carbonated water to prevent coil freeze-up. Proceed as follows to fill carbonated water system.

5.Make sure both carbonated water shutoff valves inside Cooling Unit (see Figure 2) are in ‘OPEN’(handles in line with tubing) positions.

6.Make sure Hydro Boostâ bypass valve inside Cooling Unit (see Figure 2) is in ‘CLOSED’(handle not in line with tubing) position.

7.Make sure Cooling Unit REFRIGERATION POWER, CARBONATOR MOTORS, and CIRCULATING MOTOR Power switches are in ‘OFF’(down) positions.

8.Connect electrical power to Cooling Unit at disconnect switch.

9.Place CARBONATOR MOTORS power switch in ‘ON’(up) position to start carbonators.

10.Dispense from dispensing station until carbonated water appears at valve indicating Hydro Boostâ and carbonated water system have been completely filled with carbonated water.

OPERATION

WARNING: Disconnect electrical power to Cooling Unit and Remote Condenser Coil and Fan Assembly (if applicable) to prevent personal injury before attempting any Cooling Unit or Remote Condenser Coil and Fan Assembly internal maintenance. Only qualified

personnel should service internal components or electrical wiring.

11

300381000

Page 15 Page 17
Page 16
Image 16
Cornelius 10, 000 installation manual Preparing Cooling Unit for Operation
Page 15 Page 17

000, 10 specifications

Cornelius 10,000 PLUS is a pioneering innovation in the beverage dispensing industry, designed to cater to the evolving needs of commercial establishments. This advanced system combines state-of-the-art technology with user-friendly features, making it a standout choice for restaurants, cafes, and bars aiming to enhance their beverage service.

One of the main features of the Cornelius 10,000 PLUS is its impressive capacity. With the ability to dispense a wide variety of beverages, including soft drinks, cocktails, and craft beers, the system supports a large volume of service, perfect for high-demand environments. The modular design allows for easy expansion, enabling businesses to add additional flavors or beverages as needed without major overhauls.

The technology behind the Cornelius 10,000 PLUS is equally impressive. It utilizes advanced cooling technology to ensure that beverages are served at the optimal temperature, enhancing the customer experience. The integrated touchless dispensing mechanism minimizes waste and ensures a hygienic experience, addressing growing concerns about cleanliness in food service environments. This technology also improves speed, allowing staff to serve customers more efficiently.

Another key characteristic of the Cornelius 10,000 PLUS is its digital integration capabilities. The system can be connected to a central management platform that tracks sales, inventory levels, and maintenance needs in real-time. This allows operators to optimize their beverage offerings based on customer preferences and reduces downtime through proactive maintenance alerts.

In addition to its performance features, the Cornelius 10,000 PLUS is designed with sustainability in mind. The system employs energy-efficient practices, reducing its environmental footprint while lowering operational costs. The materials used in construction are durable yet eco-friendly, ensuring longevity and less waste.

Overall, the Cornelius 10,000 PLUS stands out as an essential tool for any business looking to elevate its beverage service. With its combination of high capacity, cutting-edge technology, and sustainability features, it not only meets the demands of today’s fast-paced service environments but also positions establishments for future growth and success.
Top Page Image Contents