Manuals / Cornelius / Household Appliance / Fan

Cornelius 000, 10 Dispensed Product, Carbonation TOO LOW, Only Carbonated Water a

Models: 000 10

1 52

Download 52 pages 8.37 Kb

Page 45

Trouble

Probable Cause

Remedy

ADJUSTMENT OF DISPENSING VALVE SYRUP FLOW REGULATOR DOES NOT DECREASE TO DESIRED WATER-TO-SYRUP ‘RATIO’.

A.Dirty or inoperative piston or cylinder in dispensing valve syrup flow regulator.

A.Disassemble and clean dispensing valve syrup flow regulator.

DISPENSED PRODUCT	A. Carbonator CO2 regulator out
CARBONATION TOO LOW.	of adjustment for existing
	water conditions or
	temperature.

A.Adjust carbonator CO2 regulator as instructed.

B.Water, oil, or dirt in CO2 supply.

B.Remove contaminated CO2 supply. Clean CO2 system (lines, regulators,etc.) using a mild detergent. Replenish with a clean CO2 supply.

DISPENSED PRODUCT	A. Oil film or soap scum in cups. A. Use clean cups.
COMES OUT OF
DISPENSING VALVE CLEAR
BUT FOAMS IN CUP.

B.Ice used for finished drink is sub-cooled.

B.Do not use ice directly from freezer. Allow ice to become ‘wet’ before using. (Refer to following NOTE)

NOTE: Crushed ice also causes dispensing problems. When finished drink hits sharp edges of ice, carbonation is released from finished drink.

DISPENSED PRODUCT PRODUCES FOAM AS IT LEAVES DISPENSING VALVE.

A.Carbonator CO2 regulator pressure set too high for existing water conditions or temperature.

A.Reduce carbonator CO2 regulator pressure setting as instructed.

B.Syrup over-carbonated with CO2.

C.Tapered nylon washer inside tube swivel nut connection distorted from being overtightened restricting syrup flow.

B.Remove soft drink tank quick

disconnects. Relieve tank CO2 pressure, shake tank vigorously,

then relieve tank CO2 pressure as many times as necessary to remove over-carbonation.

C.Replace nylon washer. Make sure washer is properly seated in swivel nut.

ONLY CARBONATED WATER A.	Quick disconnect not secure	A.	Secure quick disconnect on soft
DISPENSED.	on soft drink tank.		drink tank.
B.	Out of syrup.	B.	Replenish syrup supply as
			instructed.

C.Inoperable dispensing station.

D.Dispensing valve syrup flow regulator not properly adjusted.

C.Repair dispensing station.

D.Adjust dispensing valve syrup flow regulator (refer to Installation Instructions provided with dispensing station).

300381000

40

Image 45

Cornelius 000, 10 Dispensed Product, Carbonation TOO LOW, Comes OUT Dispensing Valve Clear But Foams in CUP

Contents

This Document Contains Important Information AURORAR10,000 Cooling UnitTable of Contents Table of Contents cont’d Table of Contents cont’d LOOSE-SHIPPED Parts Cooling Unit Description General DescriptionCooling Unit Model Numbers Design DataRemote Condenser Coil and FAN ASS’Y Data P/N System Theory of OperationFlow Diagram Typical Installation Identification of LOOSE-SHIPPED Parts Unpacking and InspectionSelecting Location Cooling UnitInstalling Cooling Unit Remote Condenser Coil and FAN ASS’Y if ApplicablePlacing Cooling Unit in Location 24VAC Power Transformer Connecting Electrical Power Circuit to Cooling UnitCooling Unit factory warranty Connecting CO2 Inlet Supply Line to Cooling Unit Connecting Plain Water Inlet Supply Line to Cooling UnitCooling Unit Space Required Placing Cooling Unit in Operating PositionOperation Preparing Cooling Unit for OperationStarting Cooling Unit Refrigeration System Starting Carbonated Water Circulating PumpActivating Syrup Systems Installing Line Identification Label Dispensing Station AdjustmentsAdjusting Water Flow Rate Leak Check and Insulating Cooling Unit Outlet LinesThis page Left Blank Intentionally Cooling Unit Carbonator Motor Switch Cooling Unit Refrigeration Power SwitchCooling Unit Circulating Motor Switch Operating ControlsAdjustments Cooling Unit Maintenance Cleaning and SanitizingCleaning CO2 GAS Check Valves Periodic Inspection Preparing Cooling Unit for SHIPPING, STORING, or RelocatingPeriodic Cleaning Cleaning Condenser CoilChecking ICE Water Bath Changing ICE Water Bath FAN Assembly Item 4 300381000 Carbonator Liquid Level Control Switches Primary CO2 Regulator Carbonated Water Circulating Pump Motor LubricationIndex Part Name Secondary CO2 RegulatorsAdjusting Carbonators Tanks Liquid Levels Daily Cleaning of UnitWater Flow Rate Sanitizing POST-MIX Syrup Systems Wash Syrup SystemsFlush Syrup Systems Water Flush Syrup Systems Sanitize Syrup SystemsPurge Water OUT of Syrup Systems Restore Operation Connecting External Carbonator to Cooling Unit Cleaning CO2 System GAS Check ValvesSyrup Flavor Change Carbonators CO2 Inlet Lines CO2 GAS Check Valve300381000 300381000 Wiring Diagram LOW-VOLTAGE System Model Number Wiring Diagram HIGH-VOLTAGE System This page Left Blank Intentionally WATER-TO-SYRUP ‘RATIO’ Dispensed Drink TOOLOW or TOO High Carbonation TOO LOW Dispensed ProductComes OUT Dispensing Valve Clear But Foams in CUP Only Carbonated Water aDispensed CONT’D Only Carbonated WaterOnly Syrup Dispensed Carbonator MotorsErratic Cycling Operate Refrigeration PowerCarbonator Water Pump MotorOperate CONT’D Temperature SensingRefrigeration System Device and HIGH-PRESSURECommpressor Operates Bank CONT’D Refrigeration Flow DiagramContinuousls but does Not Form Sufficient ICEWarranty Page One Cornelius Place Anoka, Minnesota 612 800