Mounting Your Saw, Leg Set Flat Washer | Craftsman 113.29921

Mounting Your Saw

1 From the bag labeled "Base" remove the following hardware:

*4 Hex Head Screws, 5/16-18 x 1-I/8" Long *4 Hex Nuts, 5/16-18

*4 Lockwashers, 5/16" External Type

*8 Fiat Washers, tl/32 x 11/16 x 1/16

items marked with asterisk (*) are shown actual size

2 Place the saw upside down onto a smooth piece of cardboard or heavy paper, on the floor, so the saw is resting on the table top

WARNING: The saw is heavy. To avoid back injury, get help to lift the saw. Hold the saw close to your body. Bend your knees so you can lift with your

3.Place legs on saw so that holes in saw base and leg set line up and trim label is facing front. Legs will over- hang base in rear

4.Install screw, washers, lockwasher and nut as shown

5 Tighten all leg assembly and mounting hardware at this time

Hex

Leg Set

Flat Washer

End Stiffener

Flat Washer

Hex Head Screw

Saw Base

NOTE: For clarity, later manual illustrations may not show leg set attached

Bench Mounting

If you do net use the legset and prefer to mount the saw on a bench, make sure that there is an opening in the top of the bench the same size as the opening in the bottom of the saw so that the sawdust can drop through Recom- mended working height is 33 to 37 inches from the top of the saw table to the floor

5t16-18x 1-1/8 In	5/16-18
Hex Head Screw	Hex Nut

5/16 In External

Lockwasher11/32 LD.

Flat Washer

Cardb,

14-3/412

1/2--,--_l

Front of Saw

NOTE: All dimensions in inches

13

Image 13

Craftsman 113.29921 owner manual Mounting Your Saw, Leg Set Flat Washer, Bench Mounting

Contents

Rip Fence Miter Gauge Two Table ExtensionsSears, Roebuck and Co., Hoffman Estates, IL US,A Save This Manual For Future Reference Safety Signal Words Before Using The Saw Safety Instructions For Table SawWhen Installing Or Moving The Saw Sears, Roebuck and Co, D/817 WA Hoffman Estates, IL Before Each Use Dress for safety Safety Instructions For Table SawsPlan Ahead To Protect Your Eyes, Hands, Face and Ears Whenever Sawblade Is Spinning While Thru-sawing Additional Safety InstructionsGrain Featherboard Miter Cut Glossary of Terms for WoodworkingMolding 110-120Volt, 60 Hz. Tool Information Motor SpecificationsProperly Prong Plug Grounded Prong Outlet Make sure this Wire Sizes Motor Specifications and ElectricalExtension Wire Sizes Required Cord Length For A.W.G Requirements Contents Unpacking and Checking Contents Loose ListParts Loose Parts Assembling Steel Legs Installing Handwheels and Bevel Pointer Leg Set Flat Washer Mounting Your SawBench Mounting Assembling Table Extensions Assembly Installing Rip Fence Guide Bars and Switch Lockwas her Hex Nuts Lockwashers Aligning Extensions Wire TieCould be hit or cut Extension Leveling Tab Edge Checking Table Insert Installing Blade Guard Port AndBracket To Getting to Know Your Table Saw On-Off SwitchRip Fence Exacti-Cut Table Insert Tilt Handwheel Elevation Handwheel Lock Knob Push To Tighen Removing and Installing Sawblade Before Each Use Safety Instructions for Basic Saw OperationsInspect your saw Inspect Your Blade Avoid Accidental Starting Planyour cutDont Force Tool Push Stick Work Feed DevicesPush Block Making the handle Auxiliary Fence3E-l!2rL Thick Plywood Base Thick Side Plywood Finished Auxiliary Fence Additional Safety Instructions for Crosscutting Using the Miter GaugeBasic Saw Operations Crosscutting Crosscutting Bevel Crosscutting Miter CrosscuttingCompound Crosscutting Additional Safety instructions for Rip Cuts Using the Rip FenceRipping Always Support Long Or Wide Workpieces Push Block Bevel Ripping Narrow Work Using Featherboards for Thru-SawingWork Featherhoar Facing Resawing Using Featherboards for Non Thru-SawingWork Sup Ond pass Arbor LcelSaeJFence Making Mended accessories AdjustmentsPloughing and Molding Molding Cutting Rip Fence Self Aligning Spring Adjustment Adjusting Rip Scale Indicator Rip Fence Alignment AdjustmentSlide Spring To Adjust Pressure Lock Handle 3t16 To check for parallelismLocking screws Wrench Blade Tilt, or Squareness of Blade to Table Pointer Adjusting Screw With Piece Tilt and Elevation Mechanism Blade ElevationTilt Screw Screws Maintaining Your Table Saw Maintenance Pivot Nut Lubrication Remedy Sears Recommends the Following Accessories Into blade Probable Cause Parts List for Craftsman 10 Inch Fable Saw Model No Repair Parts 201 Parts List for Craftsman 10 Inch Table Saw Model No Description Parts List for Craftsman 10 Inch Table Saw Model No. t 201!17 Parts list for Craftsman 10 Inch Table Saw Key Pad No Description Parts List for Craftsman 10 Inch Table Saw Model Repair Parts Model Parts List for Craftsman 10 Inch Table Saw Rear Guide Bar Ref Model NoKey Foot Leveling Key j For in-home major brand repair service For the repair or replacement paris you needSears, Roebuck Co., Hoffman Estates, IL U.S.A