FULL ONE YEAR WARRANTY ON L,RAFTSNIAN STATIONARY TOOL

If this stationary tool fails due to adefect in material or workmanship within one year from the date
of purchase, CONTACT THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES and
Sears wilt repair it free of charge.
This warranty applies only while this product is in the United States.
If this Table Saw is used for commercial or rental purposes, this warranty will apply for ninety days
from the date of purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
Sears, Roebuck and Co°, D/817 WA Hoffman Estates, IL 60179 ..._

Safety Instructions For Table Saw

Safety isa combination of common sense, staying alert and knowing how your table saw works,, Read thismanual to
understand this table saw
Safety Signal Words
DANGER: means ifthe safety information is not followed
someone will be seriously injured or killed
Before Using The Saw
WARNING: to avoid mistakes that could cause
serious, permanent injury, do not plug the table
saw in until the following steps have been satis-
factorily completed.
*Completely assemble and align saw (See "Assembly"
section)
° Learn the use and function of the ON-OFF switch
blade guard, spreader, anti-kickback device, miter
gauge, rip fence, table insert, blade elevation and
WARNING: means ifthe safety information is not foUowed
someone could be seriously injured orkilled,
CAUTION: means if the safety information is not followed
someone may be injured,
blade tilt controls (See "Getting to Know Your Table
Saw" section),
.Review and understand all safety instructions and
operating procedures in this manual.
,Review the maintenance methods for this saw (See
"Maintaining Your Table Saw" section)),
-Find and read all the warning labels found on the saw
(shown below),
m
®
E23417
12o VoIts
3450 RP M
1t5Amp._
60 Hz_I Ph
I0"Blade
, WARNING
1, Readmanual before using saw.
2. Wearsafety goggles that meet ANSIZ87.1 Standards,
'3. DOnot reach around or oversaw blade.
4. Keepblade guarddown end In place for throughcuts.
5. Do not do freehand cuts.
6. Keephands out of path of saw blade°
7. When ripping,use push stickwhen fence Is set
2Inches ormore from blade.
8,,Know how to reduce therisk of kickback,
SeeInstructions for ripping,
9. When rlpNng, use push blockand auxiliary fence wher
fenceIsset between 1/2 end 2 Inches from blade.
Donot make dp cuts narrower than 1/2 ]nch_
l& Turn poweroff end walt for blade to stop
beforeadjustingor servicing.
When Installing Or Moving The Saw
Avoid Dangerous Environment.
•Use the saw ina dry, indoor place protected from rain,
•Keep work area well lighted
•Use recommended accessories Consult the owneCs
manual Ior recommended accessories, The use of
improper accessories may cause riskof injury topersons
To avoid injury from unexpected saw movement.
. Bott orclamp the saw to firm level surface where there is
plenty of room to handle and properly support the work-
piece (See "Assembly-Mounting Your Saw"section)
°Support the saw so the table islevel and the saw does
not rock
oWhen using a table extension longer than t2" attached
to any side of the saw, bolt the saw toa stationary sur_
face or prop upthe outer end of the extension from the
floor or bench top to keep the saw from tipping
oPut the saw where neither operator nor bystanders
must stand in line wilh the sawblade,
° To avoid injury from electrical shock, make sure your
fingers do not touch the plug's metal prongs when
plugging inor unplugging the saw,
• Never Stand On Tool Serious injury could occur if the
tool tips or you accidentally hit the cutting tool Do not
store anything above or near the tool where anyone
might stand onthe tool to reach them,