Installing Handwheels and Bevel Pointer | Craftsman 113.29921

Assembly ................. '"

Installing Handwheels and Bevel Pointer

1 From the bag labeled "Miscellaneous" remove only the following hardware:

*2 Pan Head Screws, 10 - 32 x 5/8" Long *2 Lockwashers, #10 External Type

"1 Par} Head Screw Type "T" 8-32 x 3/8 Long 1 Bevel Pointer

From the bag labeled "Large Parts" remove only the following:

2 Handwheels

Items marked with asterisk (*) are shown actual size

2, Fasten bevel pointer to cradle assembly with 8-32 x 3/8 screw, as shown. Adjustment of the pointer may be nec- essary later

3 Line up flat spots on shaft and handwheel, push handwheel onto shaft.. Install screw and !ockwasher to

lock handwheel on shaft. Repeat for the other hand- wheel

........i,,i=..... PH.....,.H ..,=......=

10-32x 5/8 In.	Type "T" 8-32 x 3/8 In.
10-32x 5/8 In.	Pan Head Screw
Pan Head Screw	Pan Head Screw
Pan Head Screw
	O	Handwheel
Bevel Pointer	#10 External
	Lockwasher

Lockwasher

	Screw	Bevel Pointer	/	Pan Head
	Tilt
		Elevation
	Handwheel	Handwheel		Screw

Assembling Steel Legs

t From the bag labeled "Legs" remove the following hardware:

"16 Truss Head Screws, 1/4-20 x 1/Z'long "16 Lockwashers, 1/4" External Type

"I6 Hex Nuts, 1/4-20

*8 Hex Nuts, 3/8-16

4 Leveling Feet

From among the loose parts find the following: 4 Legs

2End Stiffeners

2Side Stiffeners

items marked w{th asterisk (*) are shown actual size

2 Assemble the legs as shown

insert the truss head screws through the holes in the legs, then through the holes in the side and end stiffen- ers

Legs must be assembled on top of stiffeners

3 Install the Iockwashers Screw on the nuts hand tight.

4 Instal! leveling feet through hotes in bottom of legs as shown.

5 Adjust teveling feet as follows:

a Move saw to desired location..

b. With 9/16" wrench loosen bottom nut

cBack off top nut by"hand

dRaise or lower foot by adjusting bottom nut using 9/16" wrench..

e.. Snug top nut against inside of leg by hand..

f Tighten all four bottom nuts using 9/16" wrench

0©

1/4 In. External 1/4-20

1/4-20 x 112In

Lockwasher Hex Nut

russ Head Screw

Q

3/8 -16 Hex Nut

Leveling Foot

Leg

Stiffener

Side Stiffeners'_

.,,j End Stiffeners

	1/4-20	Truss Head
	1/4-20	Screw
	Hex Nut	Screw
	Lockwasher	Hex Nuts
	Leveling Foot ----_

12

Image 12

Craftsman 113.29921 owner manual Installing Handwheels and Bevel Pointer, Assembling Steel Legs

Contents

Two Table Extensions Rip Fence Miter GaugeSears, Roebuck and Co., Hoffman Estates, IL US,A Save This Manual For Future Reference Safety Instructions For Table Saw Safety Signal Words Before Using The SawWhen Installing Or Moving The Saw Sears, Roebuck and Co, D/817 WA Hoffman Estates, IL Before Each Use Safety Instructions For Table Saws Dress for safetyPlan Ahead To Protect Your Eyes, Hands, Face and Ears Whenever Sawblade Is Spinning Additional Safety Instructions While Thru-sawingGrain Featherboard Glossary of Terms for Woodworking Miter CutMolding Motor Specifications 110-120Volt, 60 Hz. Tool InformationProperly Prong Plug Grounded Prong Outlet Make sure this Motor Specifications and Electrical Wire SizesExtension Wire Sizes Required Cord Length For A.W.G Requirements Contents Unpacking and Checking Contents List LooseParts Loose Parts Installing Handwheels and Bevel Pointer Assembling Steel Legs Mounting Your Saw Leg Set Flat WasherBench Mounting Assembly Assembling Table Extensions Installing Rip Fence Guide Bars and Switch Hex Nuts Lockwashers Lockwas her Wire Tie Aligning ExtensionsCould be hit or cut Extension Checking Table Insert Leveling Tab Edge Installing Blade Guard Port AndBracket To On-Off Switch Getting to Know Your Table SawRip Fence Exacti-Cut Table Insert Tilt Handwheel Elevation Handwheel Lock Knob Removing and Installing Sawblade Push To Tighen Safety Instructions for Basic Saw Operations Before Each UseInspect your saw Inspect Your Blade Planyour cut Avoid Accidental StartingDont Force Tool Work Feed Devices Push StickPush Block Auxiliary Fence Making the handle3E-l!2rL Thick Plywood Base Thick Side Plywood Finished Auxiliary Fence Using the Miter Gauge Additional Safety Instructions for CrosscuttingBasic Saw Operations Crosscutting Crosscutting Miter Crosscutting Bevel CrosscuttingCompound Crosscutting Using the Rip Fence Additional Safety instructions for Rip CutsRipping Always Support Long Or Wide Workpieces Push Block Using Featherboards for Thru-Sawing Bevel Ripping Narrow WorkWork Featherhoar Facing Using Featherboards for Non Thru-Sawing ResawingWork Sup Ond pass LcelSaeJ ArborFence Making Adjustments Mended accessoriesPloughing and Molding Molding Cutting Self Aligning Spring Adjustment Rip Fence Rip Fence Alignment Adjustment Adjusting Rip Scale IndicatorSlide Spring To Adjust Pressure Lock Handle To check for parallelism 3t16Locking screws Wrench Pointer Adjusting Screw Blade Tilt, or Squareness of Blade to Table With Piece Blade Elevation Tilt and Elevation MechanismTilt Screw Screws Maintenance Maintaining Your Table Saw Lubrication Pivot Nut Sears Recommends the Following Accessories Remedy Probable Cause Into blade Repair Parts Parts List for Craftsman 10 Inch Fable Saw Model No Parts List for Craftsman 10 Inch Table Saw Model No 201 Parts List for Craftsman 10 Inch Table Saw Model No. t Description Parts list for Craftsman 10 Inch Table Saw 201!17 Parts List for Craftsman 10 Inch Table Saw Model Key Pad No Description Repair Parts Parts List for Craftsman 10 Inch Table Saw Model Model No Rear Guide Bar RefKey Key j Foot Leveling For the repair or replacement paris you need For in-home major brand repair serviceSears, Roebuck Co., Hoffman Estates, IL U.S.A