Blade Tilt, or Squareness of Blade to Table | Craftsman 113.29921

Adjustments (continued)

Blade Tilt, or Squareness of Blade to Table

i

,,11,,,,i

, ,i,,,

i ,i.,,,,i

When the bevel pointer is pointing directly te the "0" mark on the bevel scale, the sawblade should make a square cut 90° to the table

turn switch "OFF" and remove plug from power 1 I WARNING: To avoid injury from accidental start, ]

source outlet.

To check for squareness, 90 ° position.

1 Raise blade all the way up, raise blade guard

2 Tilt blade a few degrees to the {elt Now tilt blade back te the right as far as it will ge

3 Place the square against the blade Make sure square is net touching the tip of one of the saw teeth

4If blade is square to table; check peinter

A If pointer does net point to "0" mark en the bevel scale, bend peinter to read "0"

Pointer Adjusting

Screw

POINTER AT /

""O" POSITION_J

40

Image 40

Craftsman 113.29921 owner manual Blade Tilt, or Squareness of Blade to Table, Pointer Adjusting Screw

Contents

Two Table Extensions Rip Fence Miter GaugeSears, Roebuck and Co., Hoffman Estates, IL US,A Save This Manual For Future Reference Safety Instructions For Table Saw Safety Signal Words Before Using The SawWhen Installing Or Moving The Saw Sears, Roebuck and Co, D/817 WA Hoffman Estates, IL Before Each Use Safety Instructions For Table Saws Dress for safetyPlan Ahead To Protect Your Eyes, Hands, Face and Ears Whenever Sawblade Is Spinning Additional Safety Instructions While Thru-sawingGrain Featherboard Miter Cut Glossary of Terms for WoodworkingMolding Motor Specifications 110-120Volt, 60 Hz. Tool InformationProperly Prong Plug Grounded Prong Outlet Make sure this Motor Specifications and Electrical Wire SizesExtension Wire Sizes Required Cord Length For A.W.G Requirements Contents Unpacking and Checking Contents List LooseParts Loose Parts Installing Handwheels and Bevel Pointer Assembling Steel Legs Leg Set Flat Washer Mounting Your SawBench Mounting Assembly Assembling Table Extensions Installing Rip Fence Guide Bars and Switch Hex Nuts Lockwashers Lockwas her Wire Tie Aligning ExtensionsCould be hit or cut Extension Checking Table Insert Leveling Tab Edge Installing Blade Guard Port AndBracket To On-Off Switch Getting to Know Your Table SawRip Fence Exacti-Cut Table Insert Tilt Handwheel Elevation Handwheel Lock Knob Removing and Installing Sawblade Push To Tighen Safety Instructions for Basic Saw Operations Before Each UseInspect your saw Inspect Your Blade Avoid Accidental Starting Planyour cutDont Force Tool Push Stick Work Feed DevicesPush Block Auxiliary Fence Making the handle3E-l!2rL Thick Plywood Base Thick Side Plywood Finished Auxiliary Fence Using the Miter Gauge Additional Safety Instructions for CrosscuttingBasic Saw Operations Crosscutting Crosscutting Bevel Crosscutting Miter CrosscuttingCompound Crosscutting Using the Rip Fence Additional Safety instructions for Rip CutsRipping Always Support Long Or Wide Workpieces Push Block Using Featherboards for Thru-Sawing Bevel Ripping Narrow WorkWork Featherhoar Facing Using Featherboards for Non Thru-Sawing ResawingWork Sup Ond pass LcelSaeJ ArborFence Making Adjustments Mended accessoriesPloughing and Molding Molding Cutting Self Aligning Spring Adjustment Rip Fence Rip Fence Alignment Adjustment Adjusting Rip Scale IndicatorSlide Spring To Adjust Pressure Lock Handle To check for parallelism 3t16Locking screws Wrench Pointer Adjusting Screw Blade Tilt, or Squareness of Blade to Table With Piece Blade Elevation Tilt and Elevation MechanismTilt Screw Screws Maintenance Maintaining Your Table Saw Lubrication Pivot Nut Sears Recommends the Following Accessories Remedy Probable Cause Into blade Repair Parts Parts List for Craftsman 10 Inch Fable Saw Model No Parts List for Craftsman 10 Inch Table Saw Model No 201 Parts List for Craftsman 10 Inch Table Saw Model No. t Description Parts list for Craftsman 10 Inch Table Saw 201!17 Parts List for Craftsman 10 Inch Table Saw Model Key Pad No Description Repair Parts Parts List for Craftsman 10 Inch Table Saw Model Rear Guide Bar Ref Model NoKey Key j Foot Leveling For the repair or replacement paris you need For in-home major brand repair serviceSears, Roebuck Co., Hoffman Estates, IL U.S.A